bad main bearing
11-07-2006, 07:01 PM
#1
Registered
Thread Starter
Join Date: Sep 2004
Location: Tarpon Springs, FL Winter/LBI, NJ Summers
Posts: 497
Likes: 0
Received 0 Likes
on
0 Posts
bad main bearing
I m no machinst...took my block to machine shop, they state main bearing went along with piston, 22 degree clearance on main. My mechinic states its impossible looking at picture that it went, and clearence should be diagnosed with main caps on and torqued - which machine shop measured with cap and bearing off...who to believe. Engine had 10min run time...detonation due to leaking intake...This bearing look bad is what im asking. Thanks for the input, pardon the english.
Last edited by Dtile; 07-06-2012 at 03:15 PM.
11-07-2006, 09:31 PM
#3
Registered
Join Date: Jan 2001
Location: Holland MI
Posts: 3,140
Likes: 0
Received 0 Likes
on
0 Posts
Re: bad main bearing
That bearing definitely doesn't appear to be wiped out. It didn't spin either. It doesn't look great but it's not toasted.
Bearing clearance is measured with the bearing installed and the cap bolts torqued.
Bearing clearance is measured with the bearing installed and the cap bolts torqued.
11-07-2006, 09:40 PM
#4
Registered
Thread Starter
Join Date: Sep 2004
Location: Tarpon Springs, FL Winter/LBI, NJ Summers
Posts: 497
Likes: 0
Received 0 Likes
on
0 Posts
Re: bad main bearing
Thanks Crazy...I think Jasper is killing these local shops and they want to add work to jobs that really dont need it. Thanks for the confirmation.
11-07-2006, 10:45 PM
#5
Re: bad main bearing
Doesent look that bad ,not brased out, alittle trash in the babbit.Did its job asorbed it.
You # on clearence ?? is it .022 or .22 if its.022 that is a little tight. I bet money its not .22. if its .022 its the engine builders fault!!!! Oil presure?
What does the pistion look like?
You # on clearence ?? is it .022 or .22 if its.022 that is a little tight. I bet money its not .22. if its .022 its the engine builders fault!!!! Oil presure?
What does the pistion look like?
__________________
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
11-07-2006, 10:46 PM
#6
Registered
VIP Member
Re: bad main bearing
Originally Posted by Crazyhorse
That bearing definitely doesn't appear to be wiped out. It didn't spin either. It doesn't look great but it's not toasted.
Bearing clearance is measured with the bearing installed and the cap bolts torqued.
Bearing clearance is measured with the bearing installed and the cap bolts torqued.
11-07-2006, 10:59 PM
#9
Re: bad main bearing
Also if it leaned out/detinated it would beat out [wear]the top of the rod bearing. look at the upperbearing that the pistion is hurt.
heres a thread with some bearing picks ,last ones have 118 hours with .0027 to .0034 mains,Just took them out last week and was showing some wear
http://www.offshoreonly.com/forums/s...t=500efi+build
heres a thread with some bearing picks ,last ones have 118 hours with .0027 to .0034 mains,Just took them out last week and was showing some wear
http://www.offshoreonly.com/forums/s...t=500efi+build
__________________
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
11-07-2006, 11:13 PM
#10
Registered
Thread Starter
Join Date: Sep 2004
Location: Tarpon Springs, FL Winter/LBI, NJ Summers
Posts: 497
Likes: 0
Received 0 Likes
on
0 Posts
Re: bad main bearing
Although he wants to replace all pistons, im just going to do the one that is bad. He was able to hone the wall ok...I think ill replace all rod bearings though. And reading Raylor's post about the new main bearings they are making with a special coating might not be a bad investment.
Last edited by Dtile; 07-06-2012 at 03:15 PM.
