Go Back  Offshoreonly.com > Technical > General Q & A
Supercharger recommendation for 575SCI >

Supercharger recommendation for 575SCI

Notices

Supercharger recommendation for 575SCI

Old 09-29-2015, 10:16 AM
  #1  
Registered
Thread Starter
 
Join Date: Nov 2005
Location: Wayland, MI
Posts: 387
Likes: 0
Received 0 Likes on 0 Posts
Default Supercharger recommendation for 575SCI

I have a 2004 575 sci with the B&M blower, No logo is cast on the blower, but that is what it looks like. I have no problems with this blower so far, although I have read these blowers self destruct without warning. I am looking at options to replace it.
1. The Dyers 8-71 conversion. no chiller needed (they say). $3900.
2. Blower shop 250 $2300 plus Teague superchiller kit $2695 for 683 horsepower.
The boat has a step hull with a notch. I don't know where to put a pickup for a chiller. Looking for advice on. Thanks!
Old Navy is offline  
Old 09-29-2015, 10:23 AM
  #2  
Registered
iTrader: (2)
 
Join Date: Aug 2011
Location: bel air, md
Posts: 2,733
Likes: 0
Received 5 Likes on 5 Posts
Default

Put the puck-up in front of the step. Then you will be in clean water.
Black Baja is offline  
Old 09-29-2015, 10:29 AM
  #3  
Registered
 
Join Date: Jan 2006
Location: St. Pete Beach, FL
Posts: 3,566
Received 559 Likes on 335 Posts
Default

That things gonna fly
hogie roll is offline  
Old 09-29-2015, 10:49 AM
  #4  
Registered
iTrader: (1)
 
Join Date: Jul 2007
Location: MI
Posts: 2,639
Received 12 Likes on 6 Posts
Default

If you pull the 250 off, do not put a 250 back on. The BS 250 is a nice piece but you will still have to spin the hell out of it, even more so with the chiller. The only reason to keep the 250 is hatch clearance...if you have room for the chiller, it does not sound like an issue. The Dyres kit is decent but you can go with about any 6-71 or 8-71 and I would still use a chiller. You really only need the right length snout, a few pulleys and a lower pulley adapter from teague.

My setup is pictured here. Stripped Littlefield 8-71 with closed discharge and whipple innercooler. No need to cut a hole in your bottom for a pickup either...they slow the boat down.
Attached Thumbnails Supercharger recommendation for 575SCI-imag0556.jpg  

Last edited by JRider; 09-29-2015 at 10:52 AM.
JRider is offline  
Old 09-29-2015, 10:55 AM
  #5  
Registered
Thread Starter
 
Join Date: Nov 2005
Location: Wayland, MI
Posts: 387
Likes: 0
Received 0 Likes on 0 Posts
Default

JRider, any tips on Mefi3 programming? did you dyno that combo? It looks good.
Old Navy is offline  
Old 09-29-2015, 11:05 AM
  #6  
Registered
iTrader: (1)
 
Join Date: Jul 2007
Location: MI
Posts: 2,639
Received 12 Likes on 6 Posts
Default

I did not Dyno it with the stock cam, EB marine did the MEFI programming. I knew the programming would work because Steve Zuckerman had the same setup. I was at like 9.5 pounds boost and it was limited to 5800rpm.

I have since had the motor built with AFR heads, Lunati Cam with morel lifters and it is about ready to Dyno.
JRider is offline  
Old 09-29-2015, 11:14 AM
  #7  
Registered
iTrader: (1)
 
Join Date: Jul 2007
Location: MI
Posts: 2,639
Received 12 Likes on 6 Posts
Default

There are two guys in MI that can program the MEFI3 in the boat, Tyler Crocket and Ben at Precision Power.
JRider is offline  
Old 09-29-2015, 12:15 PM
  #8  
Registered
iTrader: (2)
 
Join Date: Aug 2010
Location: Cape Coral FL
Posts: 2,105
Received 414 Likes on 249 Posts
Default

While you are at it, ditch the stock injectors and put one of Eddie Young's plates under the throttle bodies that have 8 real injectors in it.

http://www.offshoreonly.com/forums/g...-upgrades.html

Last edited by snapmorgan; 09-29-2015 at 12:18 PM.
snapmorgan is offline  
Old 09-29-2015, 02:35 PM
  #9  
dcb
Registered
Platinum Member
 
Join Date: Aug 2007
Location: Falmouth, Va/ PGI, Fl
Posts: 448
Received 3 Likes on 2 Posts
Default

I installed the TBS blowers on my 575s - already had the whipple intercoolers and hatch clearance was limited - they are nice pieces and bolt right on. I had my Weiand blowers gone through by DMP - but still didnt trust them.
dcb is offline  
Old 09-29-2015, 04:35 PM
  #10  
Registered
iTrader: (3)
 
Join Date: Jul 2004
Location: chicago
Posts: 11,332
Received 71 Likes on 39 Posts
Default

Go with 8-71's. You wont be sorry.
MILD THUNDER is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.