Gale Banks Cam
10-04-2004, 07:43 PM
#1
Gold Member
Gold MemberThread Starter
Join Date: Oct 2002
Location: central ohio
Posts: 61
Likes: 0
Received 0 Likes
on
0 Posts
Gale Banks Cam
Does anybody know where I can find a Banks cam no. GBE*E6SCH41L. This is a hyd flat tapet 114*lobe center,.559lift.244*@.050 intake&exhaust.Lost an exhaust lobe after 18yrs.service.The cam mfgs dont have much info for turbo engines. Thanks Jack.
10-04-2004, 07:53 PM
#2
Registered
Join Date: Sep 2001
Location: Houston, TX, USA
Posts: 2,287
Likes: 0
Received 0 Likes
on
0 Posts
Re: Gale Banks Cam
I had better luck with the chev LS6 cam. It was a flat tappet cam. At least I think that was the cam. It was also on the 114 centerline. I think crane makes a equal to it.
For Turbo Cams I think the only one that still has them listed is crowler.
For Turbo Cams I think the only one that still has them listed is crowler.
10-04-2004, 08:08 PM
#3
Registered
Join Date: Sep 2001
Location: Houston, TX, USA
Posts: 2,287
Likes: 0
Received 0 Likes
on
0 Posts
Re: Gale Banks Cam
http://www.crower.com/misc/m_cat.shtml
page 45 these are not as wild as what you are saying that cam is.
If you call them they also have some grinds they do not list.
page 45 these are not as wild as what you are saying that cam is.
If you call them they also have some grinds they do not list.
10-05-2004, 07:23 AM
#4
Registered
Re: Gale Banks Cam
If you have the cam or know the profile someone can do a custom grind and duplicate it. I know Erson will and probably most other reputable cam mfg's.
10-05-2004, 12:14 PM
#5
Gold Member
Gold MemberThread Starter
Join Date: Oct 2002
Location: central ohio
Posts: 61
Likes: 0
Received 0 Likes
on
0 Posts
Re: Gale Banks Cam
Turbo Jack and Wet Vette Thanks for replies and info. I will wait & see if one of these surfaces, no hurry right now. I run rhodes lifters due to the 244*duration. It idles easily at 800 and 600 in gear with 34 bravo. I know I'm leaving some on the table but 100-102 is fast enough for my 23 1/2 footer. With this setup I don't have to service valvetrane components on a regular basis. If I don't find this cam I will have one ground identical.
04-19-2012, 11:00 AM
#7
Registered
Join Date: Apr 2012
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
cam
I have one of these cams if you are still looking for one.Its used out of a jet boat motor I bought.I have it on craigslist for 80obo you can email me at [email protected] or call me at 832 384 2936 
04-19-2012, 11:27 AM
#8
Platinum Member
Platinum Member
Personally I would have Cam Motion make it.
They do great work and will build anything.
Cam Motion, Inc.
2092 Dallas Drive
Baton Rouge, LA 70806
[email protected]
Telephone:+1 225 926 6110
Fax:+1 225 923 2101
http://www.cammotion.com/
Turbo engines too
Good Luck
Jon
