Pics of my boat
#42
Registered
Thread Starter
Join Date: Dec 2000
Location: EASTON MA.
Posts: 6,281
Likes: 0
Received 0 Likes
on
0 Posts
got used steering arms from jc now just got to get the other stuff that was stolen replaced and hope to hit the water by aug taking the motor out this weekend I have a guy driving over a case tractor to lift it out so I can fix the bulkheads check the intake for missing nuys and washers from when they stole the 1050 dom art
#43
Registered
got used steering arms from jc now just got to get the other stuff that was stolen replaced and hope to hit the water by aug taking the motor out this weekend I have a guy driving over a case tractor to lift it out so I can fix the bulkheads check the intake for missing nuys and washers from when they stole the 1050 dom art
#44
Registered
Thread Starter
Join Date: Dec 2000
Location: EASTON MA.
Posts: 6,281
Likes: 0
Received 0 Likes
on
0 Posts
YEP with my luck, I hope to have a full bulkhead all the way up the back instead of stopping at the floor and put one where the cabin dash area is with built in foot rests, when I have the money I am going to order 3 more bolsters and put them where the back seat was. well going in for operation #8 in june on the knee ,and then will need just one more after that I think. art
#45
Registered
Thread Starter
Join Date: Dec 2000
Location: EASTON MA.
Posts: 6,281
Likes: 0
Received 0 Likes
on
0 Posts
well its aug and still need the other operation, for parts just need a steering plate, carb 1050 and thats about it well the seats for the back to. I should have some new pics on here next week from last yr .the new shortie is polished this time and the b1 x drive is cool. art
#46
Registered
Thread Starter
Join Date: Dec 2000
Location: EASTON MA.
Posts: 6,281
Likes: 0
Received 0 Likes
on
0 Posts
well its aug and still need the other operation, for parts just need a steering plate, carb 1050 and thats about it well the seats for the back to. I should have some new pics on here next week from last yr .the new shortie is polished this time and the new b1 x drive is cool. still have not got the motor out but I was dreaming thinking I could hit the water this summer seats 1500, carb 1400, steering stuff 800 to 1700 so spring it will be oh well I tried art
#47
Registered
Thread Starter
Join Date: Dec 2000
Location: EASTON MA.
Posts: 6,281
Likes: 0
Received 0 Likes
on
0 Posts
with the new pics there will be gps tach pics to of the river from 79 to 80.3 got to much chine walk holding on to camera and wheel at the same time so couldn't fine tune the trim to get 83 reading so it will show 80 at 5800rpms this is from last 8/06 or 9/06. hope to havem up this weekend. art
#48
Registered
with the new pics there will be gps tach pics to of the river from 79 to 80.3 got to much chine walk holding on to camera and wheel at the same time so couldn't fine tune the trim to get 83 reading so it will show 80 at 5800rpms this is from last 8/06 or 9/06. hope to havem up this weekend. art
#49
Registered
Thread Starter
Join Date: Dec 2000
Location: EASTON MA.
Posts: 6,281
Likes: 0
Received 0 Likes
on
0 Posts
hey it was wild how quick it started once I stopped moving the steering wheel back and forth and tried to snap the pics as fast as I could it was still climbing from 79 to 80.2 or 3 and that was it, well when it hits the water it will have full steering last yr still had the add on kit. the rest is in a box art