30 Mystique before and after (well almost after) restore
#42
The whole setup looks sick!
But I have to say, those fenders hanging down so far, especially in front of the forward axle worries me. If you drop all three axles off of a boat ramp you are going to do some serious damage to the fender. If it were me, I'd have them cut down shorter.
But I have to say, those fenders hanging down so far, especially in front of the forward axle worries me. If you drop all three axles off of a boat ramp you are going to do some serious damage to the fender. If it were me, I'd have them cut down shorter.
#43
Thanks Brett
[QUOTE=kvogt;3960235]NICE. Looks real good.[/QUOTE
K your boat is sick....a lot of attention to detail, love the surface drives, just a bad ass boat all around, hope to see it in person one day... ]
Syd thanks for comments, the trailers sitting high in the ass end because theres no motors in the boat, hopfully it will level out a bit, I know the ramp very well that I use the whole trailer would have to be under the water before the wheels drop off, not saying it could happen if I take it somewhere else to boat, but I figure I can always cut them down if I have a problem, but I love the slammed look of the trailer, just built a drive guard for it also, I will post pics of that later...
I have been wet sanding, well dry sanding 800gt, 1000gt, 1500gt, 3000gt, the top half all day,fun I want to get the whole boat buffed out this weekend so I can mount the upper half SS hardware and the frame for the windscreen....
Pics of the windscreen frame I made, test fitted last night, than pulled it of this morning so I can wet sand the deck...[ATTACH=CONFIG]504594[/ATTACH][ATTACH=CONFIG]504595[/ATTACH][ATTACH=CONFIG]504596[/ATTACH]
[QUOTE=kvogt;3960235]NICE. Looks real good.[/QUOTE
K your boat is sick....a lot of attention to detail, love the surface drives, just a bad ass boat all around, hope to see it in person one day... ]
The whole setup looks sick!
But I have to say, those fenders hanging down so far, especially in front of the forward axle worries me. If you drop all three axles off of a boat ramp you are going to do some serious damage to the fender. If it were me, I'd have them cut down shorter.
But I have to say, those fenders hanging down so far, especially in front of the forward axle worries me. If you drop all three axles off of a boat ramp you are going to do some serious damage to the fender. If it were me, I'd have them cut down shorter.
I have been wet sanding, well dry sanding 800gt, 1000gt, 1500gt, 3000gt, the top half all day,fun I want to get the whole boat buffed out this weekend so I can mount the upper half SS hardware and the frame for the windscreen....
Pics of the windscreen frame I made, test fitted last night, than pulled it of this morning so I can wet sand the deck...[ATTACH=CONFIG]504594[/ATTACH][ATTACH=CONFIG]504595[/ATTACH][ATTACH=CONFIG]504596[/ATTACH]
#46
Well Lime, Gotcigs has the sistership to mine and he runs 82 with 500efis, Boomer has the other sistership to mine and he has 540efi with some work, I think it makes about 650hp and was running 94mph, my motors are 509s whipple charged AFR335 heads, crane 691 cam about 8.5 to1 comp.ratio 14qt extreme pans oilpans, haven't dynoed yet, so will see what kind of HP[ATTACH=CONFIG]504970[/ATTACH]....here's some pics, before during and now of the motor[ATTACH=CONFIG]504960[/ATTACH][ATTACH=CONFIG]504961[/ATTACH][ATTACH=CONFIG]504962[/ATTACH][ATTACH=CONFIG]504963[/ATTACH]ATTACH=CONFIG]504964[/ATTACH][ATTACH=CONFIG]504965[/ATTACH][ATTACH=CONFIG]504966[/ATTACH][ATTACH=CONFIG]504967[/ATTACHATTACH=CONFIG]50496