Offshoreonly.com

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   Fiberglass and Paint (https://www.offshoreonly.com/forums/fiberglass-paint-167/)
-   -   Fiberglass work in NJ (https://www.offshoreonly.com/forums/fiberglass-paint/113195-fiberglass-work-nj.html)

Tom A. 09-27-2005 10:50 AM

Fiberglass work in NJ
 
I am looking for a good shop that can blueprint the botom of my boat and do a few small gelcoat chip repairs.

2003 29' Kryptonite

BODYSHOT1 09-27-2005 11:40 AM

Re: Fiberglass work in NJ
 
you could try Tony Pacheco, from Bad Boy Powerboats..he's down around Egg Harbor..give Kurt @ Kurts Marine a call for a phone number...

Catagory5 09-27-2005 08:44 PM

Re: Fiberglass work in NJ
 
If Tony isn't available, you can call me at my shop. I am On the Mullica River. Marine Specialists, LLC. The shop number is 609-748-0073 or My cell 609-709-8387. We do top quality work, if i DO say so myself. I have several boats in the shop as well as a customer ref. list I would be happy to provide.

I'm assuming you have a yellow boat with twin outboards?

Hope to hear from you,
Jim Ritchie

Tom A. 09-29-2005 09:26 AM

Re: Fiberglass work in NJ
 
Hi Jim,

I have a black and white I/O that I run out of the Barnegat area. I know the yellow one you are referring to though. The bottom of my boat is white with black sides and white deck (with red and silver trim). See avitar pic. Most of the work is in the bottom with only one chip in the black gel. I also have some stains on the deck that I don't know what to do with (tree sap, dirt). I am getting a full cover for next season!

Panther 09-29-2005 04:04 PM

Re: Fiberglass work in NJ
 
Fiberglass Plus in Arnolds Marina, ask for Frank.

Catagory5 09-29-2005 08:33 PM

Re: Fiberglass work in NJ
 
Tom,
I'm less than 2 mins off the GS Parkway. If you want me to take a look at it give me a call and i can schedule some time.

Do you have some damage on the bottomr?

Either way we do expert repairs as well as custom fabrication and rigging.

Jim

Tom A. 09-30-2005 08:40 AM

Re: Fiberglass work in NJ
 
Jim, there is a chip out of the edge of the step 3" x 1/4" and some small gouges where the forks picked the boat at my marina. We had a small little mishap loading it on the trailer recently, nothing major. Also, under the swim platform, the drive was over-trimmed (when I got stuck @ the Dutchmen's :mad: ) and gouged up the bottom edge (not below water-level).

mr_velocity 09-30-2005 12:55 PM

Re: Fiberglass work in NJ
 
With the factory being so close why not take it back there?

Catagory5 09-30-2005 06:47 PM

Re: Fiberglass work in NJ
 
The dutchmans is rough!!!!!!!!!! Bring it on in or stop by and check out our shop. ON second thought don't bring it on in I couldn't get to it for a few weeks anyway but your welcom to stop by anytime. We TRY to close on Sundays. We currently are working on a 22 Apachi, 31 Cobra, 2 cali. skiboats and I have a triple engine 36 Cobra due in on the 15th as well as all the misc. "stuf"

NJgr8ful 09-30-2005 11:55 PM

Re: Fiberglass work in NJ
 
Jim I may stop by and check out the shop sometime. Got room for a 35' Cig in there before April 1st?? :D

Chris


All times are GMT -5. The time now is 08:48 AM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.