Video Drambuie on Ice Speed passes in Canada
09-25-2009, 04:37 PM
#1
Platinum Member
Platinum MemberThread Starter
Video Drambuie on Ice Speed passes in Canada
Watch this video sober the cameraman was focusing a little to much.
September 2009 Speed Run of MTI 42 Drambuie On Ice we ran 110 Octane with 850 HP motors. Multiple passes with the best pass at 122 MPH on radar and 124MPH on GPS.
This lake is very small and we had a short run up, we put smaller props and were able to get to the desired RPM for this set up.
The boat the next day ran 126 mph on Lake Champlain with plenty of space. The boat has seen 138 MPH with a set of bigger props we have.
Cranks came in on the new motors we are getting built so everything is in and they should be ready in a couple weeks we are looking at around 1150 HP per mills on 93 gas... And will dyno them also for these kinds of speed run in order to be able to have the notes of what to change running 116 OCT with jetting, timing and boost jacked up. The builder after seeing the video of this and seeing that these pulls are about 45 seconds max then 5 minute cool down says we can set up the new mills for passes like that at around 1400-1500 hp...
[YOUTUBE]http://www.youtube.com/watch?v=1hpZ9x3BUsU[/YOUTUBE]
September 2009 Speed Run of MTI 42 Drambuie On Ice we ran 110 Octane with 850 HP motors. Multiple passes with the best pass at 122 MPH on radar and 124MPH on GPS.
This lake is very small and we had a short run up, we put smaller props and were able to get to the desired RPM for this set up.
The boat the next day ran 126 mph on Lake Champlain with plenty of space. The boat has seen 138 MPH with a set of bigger props we have.
Cranks came in on the new motors we are getting built so everything is in and they should be ready in a couple weeks we are looking at around 1150 HP per mills on 93 gas... And will dyno them also for these kinds of speed run in order to be able to have the notes of what to change running 116 OCT with jetting, timing and boost jacked up. The builder after seeing the video of this and seeing that these pulls are about 45 seconds max then 5 minute cool down says we can set up the new mills for passes like that at around 1400-1500 hp...
[YOUTUBE]http://www.youtube.com/watch?v=1hpZ9x3BUsU[/YOUTUBE]
Last edited by GLH; 09-25-2009 at 04:51 PM.
09-26-2009, 12:48 AM
#8
NorTechNorth.com
Offshoreonly Advertiser
Watch this video sober the cameraman was focusing a little to much.
September 2009 Speed Run of MTI 42 Drambuie On Ice we ran 110 Octane with 850 HP motors. Multiple passes with the best pass at 122 MPH on radar and 124MPH on GPS.
This lake is very small and we had a short run up, we put smaller props and were able to get to the desired RPM for this set up.
The boat the next day ran 126 mph on Lake Champlain with plenty of space. The boat has seen 138 MPH with a set of bigger props we have.
Cranks came in on the new motors we are getting built so everything is in and they should be ready in a couple weeks we are looking at around 1150 HP per mills on 93 gas... And will dyno them also for these kinds of speed run in order to be able to have the notes of what to change running 116 OCT with jetting, timing and boost jacked up. The builder after seeing the video of this and seeing that these pulls are about 45 seconds max then 5 minute cool down says we can set up the new mills for passes like that at around 1400-1500 hp...
http://www.youtube.com/watch?v=1hpZ9x3BUsU
September 2009 Speed Run of MTI 42 Drambuie On Ice we ran 110 Octane with 850 HP motors. Multiple passes with the best pass at 122 MPH on radar and 124MPH on GPS.
This lake is very small and we had a short run up, we put smaller props and were able to get to the desired RPM for this set up.
The boat the next day ran 126 mph on Lake Champlain with plenty of space. The boat has seen 138 MPH with a set of bigger props we have.
Cranks came in on the new motors we are getting built so everything is in and they should be ready in a couple weeks we are looking at around 1150 HP per mills on 93 gas... And will dyno them also for these kinds of speed run in order to be able to have the notes of what to change running 116 OCT with jetting, timing and boost jacked up. The builder after seeing the video of this and seeing that these pulls are about 45 seconds max then 5 minute cool down says we can set up the new mills for passes like that at around 1400-1500 hp...
http://www.youtube.com/watch?v=1hpZ9x3BUsU
09-26-2009, 02:30 AM
#9
Charter Mod
Charter Member
Watch this video sober the cameraman was focusing a little to much.
September 2009 Speed Run of MTI 42 Drambuie On Ice we ran 110 Octane with 850 HP motors. Multiple passes with the best pass at 122 MPH on radar and 124MPH on GPS.
This lake is very small and we had a short run up, we put smaller props and were able to get to the desired RPM for this set up.
The boat the next day ran 126 mph on Lake Champlain with plenty of space. The boat has seen 138 MPH with a set of bigger props we have.
Cranks came in on the new motors we are getting built so everything is in and they should be ready in a couple weeks we are looking at around 1150 HP per mills on 93 gas... And will dyno them also for these kinds of speed run in order to be able to have the notes of what to change running 116 OCT with jetting, timing and boost jacked up. The builder after seeing the video of this and seeing that these pulls are about 45 seconds max then 5 minute cool down says we can set up the new mills for passes like that at around 1400-1500 hp...
http://www.youtube.com/watch?v=1hpZ9x3BUsU
September 2009 Speed Run of MTI 42 Drambuie On Ice we ran 110 Octane with 850 HP motors. Multiple passes with the best pass at 122 MPH on radar and 124MPH on GPS.
This lake is very small and we had a short run up, we put smaller props and were able to get to the desired RPM for this set up.
The boat the next day ran 126 mph on Lake Champlain with plenty of space. The boat has seen 138 MPH with a set of bigger props we have.
Cranks came in on the new motors we are getting built so everything is in and they should be ready in a couple weeks we are looking at around 1150 HP per mills on 93 gas... And will dyno them also for these kinds of speed run in order to be able to have the notes of what to change running 116 OCT with jetting, timing and boost jacked up. The builder after seeing the video of this and seeing that these pulls are about 45 seconds max then 5 minute cool down says we can set up the new mills for passes like that at around 1400-1500 hp...
http://www.youtube.com/watch?v=1hpZ9x3BUsU
Man the boat looks great.
Who did you decide to let build your new motors?
