Zuperman/myway Sale?
12-09-2009, 09:18 AM
#91
Registered
Join Date: Nov 2009
Location: New Port Richey Florida
Posts: 119
Likes: 0
Received 0 Likes
on
0 Posts
Speaking of big cats. My neighbors boat Barbed Wire which is 2007 40 Skater Flatdeck runs 188 with 1450, Jet Set which is a 1994 40 Skater runs 196 and Ruthless 2000 46 Skater lightened up as originally built ran 174 mph with Sterlings.These are local pleasure boats in NJ.
John has Tomcat the 46 Skater in NJ running pretty well with Keith Black aluminum blocks.
John has Tomcat the 46 Skater in NJ running pretty well with Keith Black aluminum blocks.
12-09-2009, 09:24 AM
#92
Charter Member
Charter Member
Speaking of big cats. My neighbors boat Barbed Wire which is 2007 40 Skater Flatdeck runs 188 with 1450, Jet Set which is a 1994 40 Skater runs 196 and Ruthless 2000 46 Skater lightened up as originally built ran 174 mph with Sterlings.These are local pleasure boats in NJ.
John has Tomcat the 46 Skater in NJ running pretty well with Keith Black aluminum blocks.
John has Tomcat the 46 Skater in NJ running pretty well with Keith Black aluminum blocks.
Sounds like you live in a REALLY COOL neighborhood!
Dean
__________________
Everything is for sale @ a certain $$
Everything is for sale @ a certain $$
12-09-2009, 09:35 AM
#93
Registered
Bob C has Speed Racer MTI as well and repowering with big power. Our other friend just purchased the 40 MTI with 850s on Pier 57. We also have a few other Skaters. My other buddy always had big power cats and just sold the 2010 40 Nortech to buy a new OL 39 with 700's. We are all waiting to see Mike's new Jet Set which should be awesome.
12-09-2009, 10:47 AM
#94
A to Z
Platinum Member
12-09-2009, 05:03 PM
#95
Registered
Join Date: Oct 2000
Location: Fresno, CA, 93722, USA
Posts: 1,436
Likes: 0
Received 4 Likes
on
4 Posts
I truly wish the trans didn't blow in Jacksonville because many would've seen what they can do. At Desert Storm, we finished putting the motor in at 2am and drove 90mph, umm wait, if there's any cops, we drove 55 to get to havasu 
We still went 167mph and that only had 1230hp with severe valve float because the wrong push rods were installed, and 1 motor was down 20psi of fuel psi because one of the pumps decided flow was not important!
Also, Justice ran 1075's in KW, it takes race fuel to go along with computer changes, and he plans on using that boat A LOT so 1200's are not really in his plans.
We still went 167mph and that only had 1230hp with severe valve float because the wrong push rods were installed, and 1 motor was down 20psi of fuel psi because one of the pumps decided flow was not important!Also, Justice ran 1075's in KW, it takes race fuel to go along with computer changes, and he plans on using that boat A LOT so 1200's are not really in his plans.
You guys seem to have a lot of engine, transmission, belt, pump, pushrod, pressure, etc etc etc issues.
Also. when going that fast. It's a good idea to watch where you are going and not have you eyes on the labtop you know.
Just a couple thoughts !!!![/QUOTE]
Do you think I'm driving, tuning and filming at the same time? Are you kidding me? Fiore was driving, laptop was data logging, I was filming. This was 1 run, normally, I'm watching the laptop. I don't drive and tune at the same time but thanks for the 411, I'll keep that in mind.
12-09-2009, 05:16 PM
#96
Registered
Join Date: Oct 2000
Location: Fresno, CA, 93722, USA
Posts: 1,436
Likes: 0
Received 4 Likes
on
4 Posts
Well in the sunlight, there is zero issues, you can't even tell there dark. With the angle, they look darker than they really are. From the inside, you can see right through. In dusk, its a bit harder to see than clear, but its really not bad.
12-09-2009, 05:28 PM
#97
VIP Member
VIP Member
12-10-2009, 04:13 AM
#99
Registered
yep
