Rotten transom Phantom 25 1985 mod
#1
Gold Member
Gold Member
Thread Starter
Rotten transom Phantom 25 1985 mod
Hi!
I hope you are well.
I have a 1985 Phantom 25 from UK with a Verado 350 sci. Its been various engines on it, included Johnsom 3.6 V8 300 GT, Promax 300 SVS, 2 x 2,5 EFI SS, etc. When we should redo the top of the transom, we suddenly discovered that the transom itself was totally soaked with water. And when we removed everything it was not a pleasant sight. Now everything is removed, and we are on our way to reinstall stringers, knees and the transom itself with divinycell, etc. Its a professional boat builder doing it, so we cross our fingers we have ol lady Phantom on the water in two weeks. Lucky us we discovered everything before a total failure.
Cheeers! Toffen
[ATTACH=CONFIG]501047
I hope you are well.
I have a 1985 Phantom 25 from UK with a Verado 350 sci. Its been various engines on it, included Johnsom 3.6 V8 300 GT, Promax 300 SVS, 2 x 2,5 EFI SS, etc. When we should redo the top of the transom, we suddenly discovered that the transom itself was totally soaked with water. And when we removed everything it was not a pleasant sight. Now everything is removed, and we are on our way to reinstall stringers, knees and the transom itself with divinycell, etc. Its a professional boat builder doing it, so we cross our fingers we have ol lady Phantom on the water in two weeks. Lucky us we discovered everything before a total failure.
Cheeers! Toffen
[ATTACH=CONFIG]501047
Last edited by Toffen; 05-19-2013 at 02:09 PM.
#3
Registered
I,ve done a few of those rotten Phantom transoms in the past ,the wood of the transom is unprotected on top by most of these older boats where the deck is not covering the top of the transom,most I,ve done were wet to the bottem.
Try to do the layup around the top and glass it in place at least 6 inches on the outer transom laminate on a shallow angle .
By looking at your pics ,it shows that your glass guy is already planning this ,by using 8 layers over the top the laminate keeps the wood together and will not bend ,best use epoxy to bond the new wood to the existing transom laminate ,but keep in mind it could take some time to get all the moisture out of the laminate .
Try to do the layup around the top and glass it in place at least 6 inches on the outer transom laminate on a shallow angle .
By looking at your pics ,it shows that your glass guy is already planning this ,by using 8 layers over the top the laminate keeps the wood together and will not bend ,best use epoxy to bond the new wood to the existing transom laminate ,but keep in mind it could take some time to get all the moisture out of the laminate .
#4
Gold Member
Gold Member
Thread Starter
Rotten transom Phantom 25
HI!
The progress is going forward. One more layer between the knees on the transom, and a divinycell plate will bond the top of the knees with the transom edge. It looks promising indeed.
In the end the transom outside and inside will be coated with gecoat. And after that a new carpet plus rerigging evererything.
Cheeers! Toffen
[ATTACH=CONFIG]501286[/ATTACH]
The progress is going forward. One more layer between the knees on the transom, and a divinycell plate will bond the top of the knees with the transom edge. It looks promising indeed.
In the end the transom outside and inside will be coated with gecoat. And after that a new carpet plus rerigging evererything.
Cheeers! Toffen
[ATTACH=CONFIG]501286[/ATTACH]
#5
Gold Member
Gold Member
Thread Starter
Totten transom Phantom 25 1985 mod
Hi!
Yes we are now soon there.
New 4 inch thick transom, knees reinforced with divinycell and new splashwell config where a dvinicell plate is bonded to the top of the knees. So the whole thing is like a box. Will be coated tomorrow, and engine +++ rigged this week. Just in time for the season
[ATTACH=CONFIG]502098[/ATTACH][ATTACH=CONFIG]502099[/ATTACH]
Cheeers, Toffen
Yes we are now soon there.
New 4 inch thick transom, knees reinforced with divinycell and new splashwell config where a dvinicell plate is bonded to the top of the knees. So the whole thing is like a box. Will be coated tomorrow, and engine +++ rigged this week. Just in time for the season
[ATTACH=CONFIG]502098[/ATTACH][ATTACH=CONFIG]502099[/ATTACH]
Cheeers, Toffen
#6
Registered
The work looks great Toff. Your Phantom makes me miss my outboard Thoroughbred. Glad to see that you will be on the water for the season.
Bob
Bob
#8
Gold Member
Gold Member
Thread Starter
Rotten transom Phantom 25 1985 model
HI!
The result was very good, and the summer even better. Next out is new interior based on Shelby GT 350 / Ford GT40 / Mach 1 I will post pictures when we start up. I may even send the boat to US for the work and do some pokerruns!
Cheeers, Toffen
[ATTACH=CONFIG]507969[/ATTACH][ATTACH=CONFIG]507970[/ATTACH][ATTACH=CONFIG]507971[/ATTACH][ATTACH=CONFIG]507973[/ATTACH][ATTACH=CONFIG]507974[/ATTACH][ATTACH=CONFIG]507975[/ATTACH]
The result was very good, and the summer even better. Next out is new interior based on Shelby GT 350 / Ford GT40 / Mach 1 I will post pictures when we start up. I may even send the boat to US for the work and do some pokerruns!
Cheeers, Toffen
[ATTACH=CONFIG]507969[/ATTACH][ATTACH=CONFIG]507970[/ATTACH][ATTACH=CONFIG]507971[/ATTACH][ATTACH=CONFIG]507973[/ATTACH][ATTACH=CONFIG]507974[/ATTACH][ATTACH=CONFIG]507975[/ATTACH]