Go Back  Offshoreonly.com > General Discussion > General Boating Discussion
496 hydroloc  help. Help help >

496 hydroloc help. Help help

Notices

496 hydroloc help. Help help

Thread Tools
 
Old 01-31-2016, 07:01 PM
  #11  
Registered
Thread Starter
 
Join Date: Aug 2004
Location: naples,florida
Posts: 4,110
Received 583 Likes on 240 Posts
Default

alarm intermintely went on and off after a short full throttle run.. i was not on the boat it is my buddies... they turned it off and it fired again no problem a few minutes later no crank hydrolock

Headgasket?
tommymonza is offline  
Old 01-31-2016, 07:01 PM
  #12  
Registered
Thread Starter
 
Join Date: Aug 2004
Location: naples,florida
Posts: 4,110
Received 583 Likes on 240 Posts
Default

no water in oil no milkyness
tommymonza is offline  
Old 01-31-2016, 07:03 PM
  #13  
Registered
 
Join Date: Oct 2015
Location: Lake George, NY
Posts: 1,244
Received 3 Likes on 3 Posts
Default

Were you loading it onto a trailer when this happened. I have noticed when people get there trailers a little too deep and get the boat on it sinks the back way down in the water and a chance to let in flow in, doesn't mater running or not. and it fills both rear cylinders
class6 is offline  
Old 01-31-2016, 07:07 PM
  #14  
Registered
 
Join Date: Oct 2015
Location: Lake George, NY
Posts: 1,244
Received 3 Likes on 3 Posts
Default

1st Thought it sounds more like a cracked exhaust manifold or riser. Your not exchanging fluids. water to oil. AND a head gaskets has to be real bad to fill a cylinder that fast
class6 is offline  
Old 01-31-2016, 07:08 PM
  #15  
Registered
Thread Starter
 
Join Date: Aug 2004
Location: naples,florida
Posts: 4,110
Received 583 Likes on 240 Posts
Default

nope just coming back to the slip

i think headgasket after a hard run. best scenaro intake.


is there anyway the manifolds or risers could cause this on a 496
tommymonza is offline  
Old 01-31-2016, 07:10 PM
  #16  
Registered
 
Join Date: Oct 2015
Location: Lake George, NY
Posts: 1,244
Received 3 Likes on 3 Posts
Default

What did the plugs look like when you took them out besides being wet. What color were they?
class6 is offline  
Old 01-31-2016, 07:11 PM
  #17  
Registered
Thread Starter
 
Join Date: Aug 2004
Location: naples,florida
Posts: 4,110
Received 583 Likes on 240 Posts
Default

so you thinking cracked manifold ?



supposedly it has brand new manifolds no indication of water in the manifold when i pulled the riser

appreciate all the input
tommymonza is offline  
Old 01-31-2016, 07:13 PM
  #18  
Registered
Thread Starter
 
Join Date: Aug 2004
Location: naples,florida
Posts: 4,110
Received 583 Likes on 240 Posts
Default

plugs clean just wet but i just glanced at them

need to crawl back down in the bilge to verify the plugs
tommymonza is offline  
Old 01-31-2016, 07:14 PM
  #19  
Registered
 
Join Date: Oct 2015
Location: Lake George, NY
Posts: 1,244
Received 3 Likes on 3 Posts
Default

Just trying to rule out the easy stuff 1st
class6 is offline  
Old 01-31-2016, 07:15 PM
  #20  
Registered
 
Join Date: Oct 2015
Location: Lake George, NY
Posts: 1,244
Received 3 Likes on 3 Posts
Default

do a compression test if you can, that will tell you
class6 is offline  


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.