How much did Bruce Dudley get from you?
05-30-2017, 07:20 PM
#43
Charter Member
So he's is still at it, eh? Surprising. LOL
__________________
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Last edited by US1 Fountain; 05-30-2017 at 07:26 PM.
05-30-2017, 10:41 PM
#44
Registered
Join Date: Aug 2011
Posts: 108
Likes: 0
Received 0 Likes
on
0 Posts
I wish I would of just googled his name a year ago. Could of saved myself a lot of time and frustration. I'm going to give him a day or two to reply to my countless calls and texts, but at this point doesn't seem that's going to happen. Once that's done I'll post up all the details, etc....
06-01-2017, 06:53 PM
#45
Registered
Join Date: Oct 2001
Location: Madison, WI
Posts: 1,153
Likes: 0
Received 0 Likes
on
0 Posts
Michael,
Bummer to hear of your misfortune. According to this thread, Bruce has become a new man and has tried to right his wrongs. Although, I haven't seen a nickel from him, a Christmas card, or a kiss my a$$ from him since my judgement against him 10 years ago. I wish you luck and please keep us updated.
Best of Luck!
Bummer to hear of your misfortune. According to this thread, Bruce has become a new man and has tried to right his wrongs. Although, I haven't seen a nickel from him, a Christmas card, or a kiss my a$$ from him since my judgement against him 10 years ago. I wish you luck and please keep us updated.
Best of Luck!
06-02-2017, 02:33 PM
#47
Registered
Join Date: Aug 2011
Posts: 108
Likes: 0
Received 0 Likes
on
0 Posts
I'm too nice of a guy, so I'm going to give him the benefit of the doubt and wait until Thursday when I'm supposed to meet him. If that doesn't happen I'll fill you in on all the excuses and stories.
04-01-2019, 04:20 PM
#48
Registered
Bruce Dudley
He got me for 10,000. Suppose to build a stock 502. Engine never had oil pressure so I finally saved enough to have it pulled out again by some reputable this this time. The boat shop owner and his engine builder pulled the pan and Bruce put stock size rods on a machined crank. Not only that but rear main seal was not put on correctly. It had used pistons, used oil pump, used timing chain. They could not believe that it stayed together. Knock sensor was disconnected valve covers were RTV’ed. I tried to call Bruce to see if he would make it right but he said nothing to help. He is a liar a crook and just terrible person. I hope one day someone screws him over like he has done to people his whole life.!
04-01-2019, 06:51 PM
#49
Member #154
Platinum Member
Join Date: Oct 2000
Location: SW CT & Long Island Sound
Posts: 7,879
Received 864 Likes
on
317 Posts
He got me for 10,000. Suppose to build a stock 502. Engine never had oil pressure so I finally saved enough to have it pulled out again by some reputable this this time. The boat shop owner and his engine builder pulled the pan and Bruce put stock size rods on a machined crank. Not only that but rear main seal was not put on correctly. It had used pistons, used oil pump, used timing chain. They could not believe that it stayed together. Knock sensor was disconnected valve covers were RTV’ed. I tried to call Bruce to see if he would make it right but he said nothing to help. He is a liar a crook and just terrible person. I hope one day someone screws him over like he has done to people his whole life.!
Wow, and nice to some old posts and members from way back (and one not with us anymore).
Last edited by Indy; 04-01-2019 at 06:55 PM.
