Go Back  Offshoreonly.com > Technical > General Q & A
purging water from the 496 cooling system >

purging water from the 496 cooling system

Notices

purging water from the 496 cooling system

Thread Tools
 
Old 11-24-2006, 11:49 AM
  #1  
Registered
Thread Starter
 
Cattitude's Avatar
 
Join Date: Jun 2001
Location: Tulsa, OK, Grand, Beaver, LOTO
Posts: 1,213
Likes: 0
Received 0 Likes on 0 Posts
Default purging water from the 496 cooling system

I've got a new to me boat- ordered the manual, but not here yet- will be colder here in a few days- how do I evacuate the water from the closed cooling??
Cattitude is offline  
Old 11-24-2006, 12:40 PM
  #2  
Registered
 
epeek's Avatar
 
Join Date: Apr 2003
Location: Lake George N.Y.
Posts: 1,530
Likes: 0
Received 0 Likes on 0 Posts
Default Re: purging water from the 496 cooling system

Take off blue pump snapped on heat exchanger. Fit on valve and pump
until tabs pop out,water will release from bottom.
***Caution,this is only for cold days in your season. Winterize with
antifreeze when putting boat up for the winter****
epeek is offline  
Old 11-25-2006, 02:15 PM
  #3  
Gold Member
Gold Member
 
Dave M's Avatar
 
Join Date: Oct 2000
Location: Hollywood, MD, USA
Posts: 5,652
Received 122 Likes on 77 Posts
Default Re: purging water from the 496 cooling system

Just expand on what epeek said....there's two little green tabs that pop out. The first one pops out after a few strokes on the pump. Make sure you keep pumping till BOTH tabs pop out.

Also, I unscrew the blue plugs on the "cool fuel" system. Even after pumping the water out as described above, a little water still comes out those blue plugs.
Dave M is offline  
Old 11-25-2006, 03:43 PM
  #4  
Registered
 
Join Date: Dec 2002
Location: 1000 Islands
Posts: 4,816
Received 42 Likes on 11 Posts
Default Re: purging water from the 496 cooling system

use a small air compressor, I do and it'll put enough air in the system to blow all the water out as well as sand blockage from the drains. Those hand pumps are a joke.
Rippem is offline  
Old 11-27-2006, 09:17 AM
  #5  
Gold Member
Gold Member
 
Rage's Avatar
 
Join Date: Sep 2005
Location: Missouri
Posts: 1,987
Likes: 0
Received 0 Likes on 0 Posts
Default Re: purging water from the 496 cooling system

Originally Posted by Rippem
use a small air compressor, I do and it'll put enough air in the system to blow all the water out as well as sand blockage from the drains. Those hand pumps are a joke.
The Merc 496 hand pump system only pressurizes the two air valves that then actuate/open the sea water drain valves which then allow the sea water to drain by gravity from the heat exchanger, cool fuel system, exhaust manifolds and associated plumbing. The engine block is part of a sealed antifreeze system.
Rage is offline  
Old 11-27-2006, 09:30 AM
  #6  
Registered
Thread Starter
 
Cattitude's Avatar
 
Join Date: Jun 2001
Location: Tulsa, OK, Grand, Beaver, LOTO
Posts: 1,213
Likes: 0
Received 0 Likes on 0 Posts
Default Re: purging water from the 496 cooling system

what about the 2 little blue wingnut drains on the lower left? drained those, are there more? I have thru hull fittings under thengines- should the system self drain by design?

Thanks for the help guys....
Cattitude is offline  
Old 11-27-2006, 11:27 AM
  #7  
Gold Member
Gold Member
 
Rage's Avatar
 
Join Date: Sep 2005
Location: Missouri
Posts: 1,987
Likes: 0
Received 0 Likes on 0 Posts
Default Re: purging water from the 496 cooling system

Originally Posted by Cattitude
what about the 2 little blue wingnut drains on the lower left? drained those, are there more? I have thru hull fittings under thengines- should the system self drain by design?

Thanks for the help guys....
The blue wing nuts drain the remaining water in the cool fuel system and the sea water pump, etc. that does not drain out with the air solenoid drain valve system described above. I believe there are three, two on one side and another on the other side but not positive.
Rage is offline  
Old 11-27-2006, 01:59 PM
  #8  
Forum Regulator
VIP Member
iTrader: (1)
 
Sydwayz's Avatar
 
Join Date: May 2001
Location: Worldwide
Posts: 23,828
Received 1,195 Likes on 519 Posts
Default Re: purging water from the 496 cooling system

5 total blue drain plugs per engine.

2 on water pump assembly.
Sydwayz is offline  
Old 11-27-2006, 03:12 PM
  #9  
Registered
 
Join Date: Dec 2002
Location: 1000 Islands
Posts: 4,816
Received 42 Likes on 11 Posts
Default Re: purging water from the 496 cooling system

Originally Posted by Rage
The Merc 496 hand pump system only pressurizes the two air valves that then actuate/open the sea water drain valves which then allow the sea water to drain by gravity from the heat exchanger, cool fuel system, exhaust manifolds and associated plumbing. The engine block is part of a sealed antifreeze system.
Your kidding right? So that's what that pink stuff was draining into my bilge???



Use compressed air to assure complete opening, and save some time.

try it you'll like it.

Last edited by Rippem; 11-27-2006 at 03:56 PM.
Rippem is offline  
Old 11-27-2006, 03:28 PM
  #10  
Registered
 
Join Date: Mar 2003
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Default Re: purging water from the 496 cooling system

This year after purging all water out and pulling the blue plugs,and them reinstalling them, I ran rv antifreeze with ear muffs and then just left it in there.Won`t be a dry start next year..its good for -18.
bcolmsted is offline  


Quick Reply: purging water from the 496 cooling system


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.