600sci Stainless Coolant Reservoir Cylinders
#11
Registered
Join Date: May 2002
Location: North of the Border
Posts: 860
Likes: 0
Received 0 Likes
on
0 Posts
here is a better angle picture of the engine compartment, when finished, which shows the site glass along the side of the stainless tank.
As far as clearance, this picture also gives you an idea of where the tank sits compared to the top of the engine. Then again, the 600 blower sits higher than a 525 would.
As far as clearance, this picture also gives you an idea of where the tank sits compared to the top of the engine. Then again, the 600 blower sits higher than a 525 would.
#12
Registered
Aie Thank`s for the picture ....can you take some measurement ??? just to have a idea of how many quantity the reservoir can hold ??.....and if you have your boat near ...some closer shot of the patern of the hose...just to help me to figure how to made it ...and if i am lucky ..i will can be able to show you my work at the Sunsation Rally this next summer
#13
Registered
Join Date: May 2002
Location: North of the Border
Posts: 860
Likes: 0
Received 0 Likes
on
0 Posts
Hey Mentalpause ...can you send me the picture not resize ???..at my email adress [email protected]`s agin to take time
#14
Registered
Hey Mentalpause ...can you send me the picture not resize ???..at my email adress [email protected]`s agin to take time
#15
Registered
Join Date: May 2002
Location: North of the Border
Posts: 860
Likes: 0
Received 0 Likes
on
0 Posts
Thank's to take time
#16
Registered
I do not have a full res version of the picture. When it was taken I had the camera set in a compressed moderate mode so I would not have to resize the pictures.
#17
From: "Tony Esposito" <[email protected]>
To: "Steve Bonillas" <[email protected]>
Subject: RE: *****SPAM***** Coolant Reservoir
Date: Friday, February 09, 2007 11:42 AM
Steve:
We do not offer a stainless reservoir. You might check with Livorsi
Marine or Teague Custom Marine. We would be happy to make one for you,
but I'm guessing it would be less expensive to buy something off the
shelf than it would be for us to design and build it.
We appreciate your interest and sorry we can not help.
Strike 1, I will try Sunsation next...
To: "Steve Bonillas" <[email protected]>
Subject: RE: *****SPAM***** Coolant Reservoir
Date: Friday, February 09, 2007 11:42 AM
Steve:
We do not offer a stainless reservoir. You might check with Livorsi
Marine or Teague Custom Marine. We would be happy to make one for you,
but I'm guessing it would be less expensive to buy something off the
shelf than it would be for us to design and build it.
We appreciate your interest and sorry we can not help.
Strike 1, I will try Sunsation next...
#18
Registered
Talked to Moriarty on some other items yesterday and we got into talking about this. The stainless tanks bolt right up to the housing that is there. Existing hoses, although one needs to be shortened, hook right up. You use the cap from the merc container and put it on the stainless container.
#19
Registered
Join Date: May 2002
Location: North of the Border
Posts: 860
Likes: 0
Received 0 Likes
on
0 Posts
Talked to Moriarty on some other items yesterday and we got into talking about this. The stainless tanks bolt right up to the housing that is there. Existing hoses, although one needs to be shortened, hook right up. You use the cap from the merc container and put it on the stainless container.
Thank`s John .... what i will do is take a 6 " inches stainless pipe ...and plug the bottom ...and for the top made it for fit with the Merc Cap ..... and after send the tank to chrome shop .... i will show you in the near futur the result ...
Have a good day
and if someone have a close picture of the tank ....feel free to post it here