Go Back  Offshoreonly.com > Technical > General Q & A
604 c.i.  Quad Whipple Project >

604 c.i. Quad Whipple Project

Notices

604 c.i. Quad Whipple Project

Old 04-27-2010, 07:27 AM
  #41  
Registered
 
Join Date: Mar 2009
Location: Delaware
Posts: 1,194
Likes: 0
Received 1 Like on 1 Post
Default

Looks great man. Can't wait to see some videos.
Philm is offline  
Old 04-27-2010, 07:39 AM
  #42  
Registered
iTrader: (2)
 
Join Date: Mar 2003
Location: Dallas
Posts: 3,064
Received 61 Likes on 22 Posts
Default

I remeber this boat. I think I rode in it with the 1000 HP setup and bravos when the original owner had it.

Nice build up. I wish you the best with the drives.
TxHawk is offline  
Old 04-27-2010, 07:52 AM
  #43  
Gold Member
Gold Member
 
CcanDo's Avatar
 
Join Date: May 2002
Location: DFW
Posts: 1,127
Likes: 0
Received 0 Likes on 0 Posts
Default

Congratulations !!! Nice engines !!!
CcanDo is offline  
Old 04-27-2010, 08:46 AM
  #44  
Registered
Thread Starter
iTrader: (4)
 
Join Date: Oct 2002
Location: Bowling Green, Kentucky
Posts: 1,975
Received 40 Likes on 22 Posts
Default

Thanks for the kind words. Tx Hawk I'd like to hear more about the boats performance, props with the 1000's, Bob T. Told me they were in there.
SkiDoc is offline  
Old 04-27-2010, 04:28 PM
  #45  
Charter Member #601
Charter Member
 
Mr Gadgets's Avatar
 
Join Date: Dec 2000
Location: Holland, Mi USA.
Posts: 3,276
Received 4 Likes on 3 Posts
Default

Looking Awesome!! Lets us know what power you make with them.
I agree, they will be better suited to low rpm. So apply that power easy to those drives!!

Dick
Mr Gadgets is offline  
Old 04-27-2010, 06:24 PM
  #46  
Registered
Thread Starter
iTrader: (4)
 
Join Date: Oct 2002
Location: Bowling Green, Kentucky
Posts: 1,975
Received 40 Likes on 22 Posts
Default

Dick looks like I'm going to put your drives to the test. I know I'll have a very easy hand with them. I would just sell them before I torture them except I don't want to change the whole set up. I'd like to get some base line numbers before I go to the SCX's.
SkiDoc is offline  
Old 04-28-2010, 10:16 AM
  #47  
Registered
 
Join Date: Jan 2004
Location: Tennessee
Posts: 4,480
Likes: 0
Received 40 Likes on 16 Posts
Default

I'll be on the dyno tomorrow with them. I have an NA 547 to do first, then Eric's Quadrotors are going on. I will be sure to shoot some video and post it for you guys to see. We are only looking to make about 1000-1050 HP, so it should be fairly easy. We're gonna do what we can to keep those drives in one piece. I'll post the results as soon as I get them. Thanks everyone.
Eddie
Young Performance is offline  
Old 04-28-2010, 09:27 PM
  #48  
Registered
 
Join Date: Aug 2004
Location: Paducah KY KY Lake
Posts: 3,812
Likes: 0
Received 2 Likes on 2 Posts
Default

Congrats Eric engines look awesome... good job Eddie.
customryder is offline  
Old 04-28-2010, 10:30 PM
  #49  
Registered
 
Join Date: Jul 2005
Location: evansville In
Posts: 482
Likes: 0
Received 0 Likes on 0 Posts
Default

They look great now Eric !!!!!!!!!!!! Can't wait to see them in the cat at the Ky. poker run!! Are the heads out of the box or worked a little?
speedreeder is offline  
Old 04-29-2010, 01:48 AM
  #50  
Registered
 
Join Date: Jan 2004
Location: Tennessee
Posts: 4,480
Likes: 0
Received 40 Likes on 16 Posts
Default

They are out of the box as far as the ports go. I did some work opening up the oil drain holes, etc. but did not touch the ports or runners.
Eddie
Young Performance is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.