Go Back  Offshoreonly.com > Technical > General Q & A
are these made any more? >

are these made any more?

Notices

are these made any more?

Thread Tools
 
Old 02-18-2016, 04:59 PM
  #1  
Platinum Member
Platinum Member
Thread Starter
 
whiskeyhangover's Avatar
 
Join Date: Jun 2012
Location: Jefferson, Ga
Posts: 205
Likes: 0
Received 1 Like on 1 Post
Default are these made any more?

Air diverter for a clamp on exhaust... Hardin Marine said their replacement ram won't work and i can't find who made these. Thanks[ATTACH=CONFIG]551233[/ATTACH][ATTACH=CONFIG]551233[/ATTACH]
Attached Thumbnails are these made any more?-20160218_162647-1.jpg  
whiskeyhangover is offline  
Old 02-18-2016, 05:10 PM
  #2  
Platinum Member
Platinum Member
Thread Starter
 
whiskeyhangover's Avatar
 
Join Date: Jun 2012
Location: Jefferson, Ga
Posts: 205
Likes: 0
Received 1 Like on 1 Post
Default

Here are the clamp ons.[ATTACH=CONFIG]551236[/ATTACH]
Attached Thumbnails are these made any more?-20160218_180214.jpg  
whiskeyhangover is offline  
Old 02-18-2016, 06:09 PM
  #3  
Geronimo36
Gold Member
 
Panther's Avatar
 
Join Date: Sep 2002
Location: Elkton, MD
Posts: 11,972
Received 131 Likes on 36 Posts
Default

Check McMaster Carr, they have a ton of that stuff and 1/2 the cost.
Panther is offline  
Old 02-18-2016, 06:41 PM
  #4  
Registered
 
Join Date: Oct 2010
Location: Hemlock, MI
Posts: 922
Received 127 Likes on 74 Posts
Default

I tried this year to find a set of cylinders to operate a set on my shelf. Yes McMaster Carr has something that will work, but not exactly the same. Issue here is that originally they are fitted like a double acting cylinder but have a return spring installed. The way they work is only single acting however and the backside port was piped inside the boat to keep water out of the cylinder when they sucked air back in when dump solenoid released. You can get very cheap throw away single acting cylinders that bolt right on but have only one port. There is a bleed hole for the back side only that could suck water in. Probably would last a few years and they are cheap enough to be disposable. If you get a double acting cylinder, you will need to figure out a way to pressure both sides to move the piston, or get an expensive rebuildable model and install a return spring on your own.
Gimme Fuel is offline  
Old 02-18-2016, 06:57 PM
  #5  
Were doomed!
Charter Member
iTrader: (1)
 
Wally's Avatar
 
Join Date: Oct 2000
Location: Chicago, IL
Posts: 6,699
Received 939 Likes on 471 Posts
Default

try looking up the company's Festo or Parker, they can get you what your looking for....just have to call them and tell them what your looking for.
__________________
-Wally

Money can't buy happiness, but it can buy horsepower. And I've never seen a sad person hauling a$$!
Wally is offline  
Old 02-19-2016, 03:49 AM
  #6  
Registered
Platinum Member
 
Join Date: Jan 2006
Location: wisconsin
Posts: 688
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by whiskeyhangover
Here are the clamp ons.[ATTACH=CONFIG]551236[/ATTACH]
They look like a CMI custom made to order muffler. Call Dave Rank at Custom Marine they have them in stock.
Bawana is offline  
Old 02-19-2016, 12:42 PM
  #7  
Charter Member # 55
Charter Member
 
Griff's Avatar
 
Join Date: Oct 2000
Location: Omaha/LOTO
Posts: 19,555
Received 1,816 Likes on 904 Posts
Default

The ends caps will come off. It may not be easy to get them off, but they will come apart. Then just replace the O rings inside.
Griff is offline  
Old 02-19-2016, 12:51 PM
  #8  
Registered
iTrader: (1)
 
Join Date: Aug 2004
Location: Whitefish Chain - Crosslake, MN
Posts: 430
Received 3 Likes on 3 Posts
Default

I have a Gaffrig muffler with an actuator like that. If you only need one, I may be able to help you. What are the dimensions?
ACrooks69 is offline  
Old 02-19-2016, 08:42 PM
  #9  
Platinum Member
Platinum Member
Thread Starter
 
whiskeyhangover's Avatar
 
Join Date: Jun 2012
Location: Jefferson, Ga
Posts: 205
Likes: 0
Received 1 Like on 1 Post
Default

Need 4. I ordered some for McMaster Carr so I'll see if the ones I've got coming will work. Thanks though.
The dimensions are:
6.44" retracted
8.44" expanded
3/4" bore
1/4 " shaft

Last edited by whiskeyhangover; 02-19-2016 at 08:46 PM.
whiskeyhangover is offline  
Old 02-20-2016, 08:49 AM
  #10  
Registered
 
Join Date: Jan 2006
Location: Minneapolis
Posts: 715
Likes: 0
Received 4 Likes on 4 Posts
Default

Pick your poison,

http://www.bimba.com/Products-and-Cad/Actuators/Inch/

Jeff
hallj is offline  


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.