Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: AfterHours
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Forum: General Q & A
05-28-2010, 10:00 AM
Replies: 3
Views: 2,030
Posted By AfterHours

Smartcraft Guage problem

I have a tri-toon that came with a 350 mag in it with smartcraft and we put a 496 HO engine in with smartcraft. Everything hooked up fine and the boat runs awesome. All systems monitor good with a...
Forum: General Q & A
12-18-2006, 02:02 PM
Replies: 4
Views: 879
Posted By AfterHours

496 H.O. Buildup

I have a 496 H.O. that we want to get an additional 75-100HP out of. The boat has smartcraft. What suggestions does anyone have?
Forum: General Q & A
04-12-2006, 11:56 AM
Replies: 36
Views: 7,194
Posted By AfterHours

Re: Help I'm in starter He!!

Dyno, On the older Chevy blocks mostly in 4X4 trucks the machining tolerance on the blocks weren't so great. We used to always try to keep the starter with the original block but when you couldn't...
Forum: General Q & A
01-12-2006, 12:40 PM
Replies: 9
Views: 976
Posted By AfterHours

Question Cylinder leakage

I am trying to build my own cylinder leakage tester using very accurate guages and regulator. Has anyone ever build their own and how do I figure how big of a restriction I need between the guages. I...
Forum: General Q & A
05-25-2005, 09:38 AM
Replies: 7
Views: 12,329
Posted By AfterHours

Re: Will a double roller timing chain fit under the timing cover on a 454 Gen V?

No. You can by a timing cover that will allow you to use a double roller. I got it from Comp. all aluminum, not cheap. I then also used an older style cam. Nice cover but I also had to grind a couple...
Forum: General Q & A
04-11-2005, 10:27 AM
Replies: 9
Views: 5,599
Posted By AfterHours

Re: whats a "rev kit" ???

I used to run them on Big Blocks several years ago, One set I had was a crane and the others where made by Jomar I believe. They were used a lot in drag racing and truck pulling on engines with real...
Forum: General Q & A
03-07-2005, 09:20 AM
Replies: 25
Views: 28,473
Posted By AfterHours

Re: Tricks for rounded off head bolt?

Weld a nut on top of the head of the bolt. Use a big enough nut so you can get a good weld inside the nut and to the top of the bolt. If there's room, use a nut that will go over the bolt head and...
Forum: General Q & A
11-01-2004, 08:50 AM
Replies: 27
Views: 4,803
Posted By AfterHours

Re: No Oil Pressure after oil change to Synthetic?

Try putting your oil filter back on along with the cooler and pull the cooler return line off at the block. Then spin the oil pump with your drill, this will show you if the oil will flow through...
Forum: General Q & A
09-02-2004, 12:26 PM
Replies: 67
Views: 16,650
Posted By AfterHours

Re: New Gm 454 Ho Motor Advice

What was your engine running at for temps before they let go? As everyone has said, marine engines are clearanced a little more than regular automotive. If you are running to cold, the aluminum...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.