30 Skater twin 300XS's Pics and test results
#31
Registered
Platinum Member
Thread Starter
Join Date: Jun 2005
Location: California Delta
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
I had a chance to run it tonight.
As I guessed, it is over propped. It wouldn't pull 'em past 5500
which was somewhere around 95mph.
I am going to look for a set of 4 blade cleavers in a 32 or 34 for my next run.
My gaurdian came on twice tonight at 5500rpm for a overheating sensor. This is a new issue. I assume it's because of the increased load the 34 Bravo's were putting on the motors.
My water pressure seems very low, usually around 5-7psi. Anybody with experience with 300XS's and water pressure? I am told 300x motors should never get under 15psi. 300XS the same? I may try lowering the motors a 1/4 inch.
As I guessed, it is over propped. It wouldn't pull 'em past 5500
which was somewhere around 95mph.
I am going to look for a set of 4 blade cleavers in a 32 or 34 for my next run.
My gaurdian came on twice tonight at 5500rpm for a overheating sensor. This is a new issue. I assume it's because of the increased load the 34 Bravo's were putting on the motors.
My water pressure seems very low, usually around 5-7psi. Anybody with experience with 300XS's and water pressure? I am told 300x motors should never get under 15psi. 300XS the same? I may try lowering the motors a 1/4 inch.
#32
Registered
Join Date: Jul 2003
Location: miami fla.
Posts: 1,554
Likes: 0
Received 0 Likes
on
0 Posts
[QUOTE=ExtremeSkater;2172594].
I am going to look for a set of 4 blade cleavers in a 32 or 34 for my next run.
if your gonna get 4 blades talk with racesdad I got a set of props from him and tried another 3 blade to see the diffrence (but couldnt turn too big) his props are clean like new, Im sure he has a set of cleaver outboard wheels 4 bladers that he wants to get rid off....call Mike hes straight up and nice to work with..
I am going to look for a set of 4 blade cleavers in a 32 or 34 for my next run.
if your gonna get 4 blades talk with racesdad I got a set of props from him and tried another 3 blade to see the diffrence (but couldnt turn too big) his props are clean like new, Im sure he has a set of cleaver outboard wheels 4 bladers that he wants to get rid off....call Mike hes straight up and nice to work with..
#33
Registered
Join Date: Aug 2006
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
I had a chance to run it tonight.
My gaurdian came on twice tonight at 5500rpm for a overheating sensor. This is a new issue. I assume it's because of the increased load the 34 Bravo's were putting on the motors.
My water pressure seems very low, usually around 5-7psi. Anybody with experience with 300XS's and water pressure? I am told 300x motors should never get under 15psi. 300XS the same? I may try lowering the motors a 1/4 inch.
My gaurdian came on twice tonight at 5500rpm for a overheating sensor. This is a new issue. I assume it's because of the increased load the 34 Bravo's were putting on the motors.
My water pressure seems very low, usually around 5-7psi. Anybody with experience with 300XS's and water pressure? I am told 300x motors should never get under 15psi. 300XS the same? I may try lowering the motors a 1/4 inch.
During a high speed run, one of the compressors came apart (it seems that it was assembled without any loctite) and I am having it replaced under warranty. I hope to be testing next weekend again.
Nice looking boat you gotĄĄ good luck....
#35
Registered
Join Date: Apr 2001
Location: Atlanta / Ft. Myers Fl.
Posts: 794
Likes: 0
Received 0 Likes
on
0 Posts
I have a set of 300 XS on my 28 skater, and I am still struggling to get it propped right. As far as the guardian system, it will come on when water pressure hits below 12 psi, so try to keep 12-15 as a minimum. It will also beep at 6400 rpm, if RPMīs donīt drop within 5 seconds, the guardian will kick in and drop your rpmīs. The engines are well protected by the guardian system. I am running 34 X 14.5 3 blade labbed cleavers for a top speed of 107 mph at 6350 rpmīs but ocassionally hit the rev limiter. I have a set of 36 X 15 on the way to test.
During a high speed run, one of the compressors came apart (it seems that it was assembled without any loctite) and I am having it replaced under warranty. I hope to be testing next weekend again.
Nice looking boat you gotĄĄ good luck....
During a high speed run, one of the compressors came apart (it seems that it was assembled without any loctite) and I am having it replaced under warranty. I hope to be testing next weekend again.
Nice looking boat you gotĄĄ good luck....
Are you turning your drives in or out ?
#36
Registered
Mint Boat! Good luck with it. Love the paint!
#37
Registered
Platinum Member
Thread Starter
Join Date: Jun 2005
Location: California Delta
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
Anyways, what water psi did you have prior to your dual pickups and what do you have now with them?
#39
Registered
Platinum Member
Thread Starter
Join Date: Jun 2005
Location: California Delta
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
I lowered the motors about a 1/4 inch today. Now I have 7-15psi. I have to re-test with another set of props to see if I lost any top end.
#40
Registered
Join Date: Aug 2006
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts