Missing an engine?
 

A storage facility in FL is trying to unload this engine,tranny and exhaust. Could be and hope it is legit on Ebay. Just looks out of place.

maybe termites ate the wooden boat it was in:cool-smiley-011:

Maybe it's to satisfy an unpaid storage or repair bill...

whats the ebay # :cool-smiley-026:

It will be posted again on ebay soon. I bid and won it for $3000. It was advertised as a tall deck 510 in with aftermarket iron ported and polished heads. After I won it I was emailed all the part # I was wating for. Ran the # and found GM rec port heads and a bow tie short deck block so I passed on the deal.

what was the # you won ??????

Just Emailed the guy, he says it will be posted today or tomorrow on ebay. You only get the long block,exhaust tranny,bell housing and acc do not go with the engine.

Why would you start a thread with no link , or # ??? did you want guys from OSO to bid against you ??? never found any motor that matched the pic you listed ,was this your motor your trying to unload ??:evilb::evilb:

Burr?
 

Got a burr up your a$$, whats your problem? As stated, the engine gets relisted today or tomorrow. There is no link, I bid and won it so the link is removed. No its not mine, just trying to inform fellow OSO members if they have lost an engine to view this one. You obviously want this engine so wait till its listed again you pissy *****. P.S. Hope your day gets better. Andy...

:food-smiley-007:

:party-smiley-004:

All my days are GREEEEAAAAT , looks like you dont know Dik about ebay cause you can still use the listing # to look up for 90 days after auction close . ROCK ON ITS A SKATER NATION !!!!!!!!!!!!!!!!!!!!!!! good luck with the motor :Whatever:

Whoa. :party-smiley-004:

***** *****
 

Hey PIS*Y BIT*H just relisted #190189395852

"Burning bridges, one post at a time".

Someones got to L@@k out for me while STECZ buzy LMAO
thnx Darlin:D:D

Thnx dude send it to jeff1000man he'll buy it
play safe :cool-smiley-027:

Just PM'd Jeff and Smiklos also(before looking at your post)I hope he can use it. You have to be careful of how it's worded it sounds like he is listing it with Edelbrock 454R heads and a Junior Victor intake but the front of the heads have the casting plug and the part #'s listed are for iron heads. Andy...

It is nothing but a block with **** heads and to much monies but he may hook someone on ebay who does'nt read and looks at pics .. I sent him an offer of 750.00 if he takes it ok if not JEFF is a lil cheaper and will prob offer him 500.00
thnx pi*sy Bit*h
LMAO

Cheers !

Somehow i dont think the dyno sheet will be for this motor , no blower and 850 hp that is incredable . the 496 we're building with a 250 blower & 5 lbs will make 600 hp and hopefully 650 and i think jeff built 2 the same set up . i wonder if they'll put it back on the dyno if i pay the set up and breakdown if it make the 850 ... it will be interesting if he takes the offer and we go down to check the bearings and do a comp test
thnx for the info :cool-smiley-011:

jeff1000man is busy getting tanked with my brother on the lake right now........looks like he will have some PM's to go through

Hey TBONE whats with that chit ??? did'nt anyone tell them its winter LOL i sure hope they brought a half dozen of those SILICONE filled pfds LMAO

Guys, don't argue! The link dosen't matter, anyone needs a good set of motors, here they are http://www.offshoreonlyclassifieds.c...o20664-en.html

Screw that Ebay crap!!:D:D

Just try'n to help!!:D

Those are some nice mills for 50 G's :cool-smiley-011:

Damn, that is a steal. I wish I had an extra 50 g's laying around. Will ya take payments? :D