|
https://cimg2.ibsrv.net/gimg/www.off...4336befeb8.png
LML 6.6 https://cimg6.ibsrv.net/gimg/www.off...d712c11a07.png 316 SS log headers https://cimg0.ibsrv.net/gimg/www.off...628c2ae253.png 3in outer casing. Not sure why I didn’t use v band clamps here instead of the flanges but... https://cimg6.ibsrv.net/gimg/www.off...0e36862a92.png Heads had to be shipped out to so cal diesel to machine the injector bores to fit LMM sticks. Turned out at the time no one had figured out how to delete the VATS in the LML ecm but the LML bottom ends were considered stronger with better oil squirters. So they are LML’s with LMM fuel systems. All stock internal except for AF cams. https://cimg7.ibsrv.net/gimg/www.off...0ab6fc80a4.png 316 schedule 10 pipe for log headers and up pipes. https://cimg1.ibsrv.net/gimg/www.off...804662f326.png Fitted then tacked with mig. Tig welded next morning. https://cimg3.ibsrv.net/gimg/www.off...3196d6bf6f.png Sometimes ya just do what you have to do. never claimed to be an engineer. I did learn to Tig weld after leaving a couple small parts at welding shops and waiting weeks for a 20 minute to get done. |
https://cimg5.ibsrv.net/gimg/www.off...d9eb595ba8.png
Center mounts with zinc chromate coating. https://cimg9.ibsrv.net/gimg/www.off...55b7d36206.png Mixer elbows. https://cimg0.ibsrv.net/gimg/www.off...10720166db.png Stock turbo housings with v band snouts. https://cimg3.ibsrv.net/gimg/www.off...345f65a846.png Intake horns. |
https://cimg7.ibsrv.net/gimg/www.off...1103d75134.png
Ready to bolt on trans and dry fit engines and intercoolers. https://cimg1.ibsrv.net/gimg/www.off...f200e24b24.png https://cimg9.ibsrv.net/gimg/www.off...862bef1605.png Dry fit then pull out and paint the bilge. Intercooler tubing just mocked up at this point, automotive type power steering reservoir were later replaced by Latham marine. |
https://cimg1.ibsrv.net/gimg/www.off...9803d0a50.jpeg
Stand alone harness Ken Wolkens Melbourne Fl Throttle and Gateway harness Ken Riggs Ohio |
https://cimg7.ibsrv.net/gimg/www.off...d4d2ca2b2.jpeg
https://cimg8.ibsrv.net/gimg/www.off...b71e36d5a.jpeg Strb engine was run on the stand ( can’t upload video) Back in boat waiting for different tunes for ecm, otherwise ready to go. |
https://cimg1.ibsrv.net/gimg/www.off...e736798188.png
Port exhaust mock up https://cimg8.ibsrv.net/gimg/www.off...2fb769e75.jpeg Port exhaust https://cimg3.ibsrv.net/gimg/www.off...3c7266c9c.jpeg 5in SS flapper in side exhaust. 5in of drop from mixer elbow down to flapper. https://cimg4.ibsrv.net/gimg/www.off...d5191176d.jpeg Livorsi fly by wire throttles programmed for Duramax ecm. Thanks to Kid Turbo for these. |
https://cimg6.ibsrv.net/gimg/www.off...01d3445ea.jpeg
https://cimg8.ibsrv.net/gimg/www.off...8deb75f20.jpeg https://cimg3.ibsrv.net/gimg/www.off...c9ce68825.jpeg https://cimg5.ibsrv.net/gimg/www.off...56ae0a988.jpeg https://cimg7.ibsrv.net/gimg/www.off...901feb14e.jpeg https://cimg9.ibsrv.net/gimg/www.off...d89ddc525.jpeg Most of the rigging done. This is pretty much where I am today. Need to wire up engine harness and stand alone harness port engine. Reprogram ecm. Put back in boat. Tie in power steering. Install drives and hope the props are close to being right. |
|
|
How long has this project taken you?
|
| All times are GMT -5. The time now is 03:51 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.