cross post -- need help fast please
#1
Registered
Thread Starter
Join Date: Nov 2002
Location: Huntersville, NC
Posts: 641
Likes: 0
Received 0 Likes
on
0 Posts
cross post -- need help fast please
hey guys
need help pretty quickly -- got a motor guy putting my boat back together -- he is not a marine person
motor is in ready to fire -- ive got a merc II tranny and trs drive -- on the tranny there are two water lines (cooler)-- i'm assuming one goes to the rear port of the exhaust as an exit -- but where does the inlet line go to?
can i just tee off of the outlet of the raw water pump -- prior to it going into the block?
this is a new motor and i don't have any of the old stuff for reference.
thanks for a quick reply -- i need to call him so i can have my boat back!!!
mark
need help pretty quickly -- got a motor guy putting my boat back together -- he is not a marine person
motor is in ready to fire -- ive got a merc II tranny and trs drive -- on the tranny there are two water lines (cooler)-- i'm assuming one goes to the rear port of the exhaust as an exit -- but where does the inlet line go to?
can i just tee off of the outlet of the raw water pump -- prior to it going into the block?
this is a new motor and i don't have any of the old stuff for reference.
thanks for a quick reply -- i need to call him so i can have my boat back!!!
mark
#2
Registered
Join Date: Dec 2000
Location: EASTON MA.
Posts: 6,281
Likes: 0
Received 0 Likes
on
0 Posts
Re: cross post -- need help fast please
do you have a factory oil,powersteering cooler or is it missing.my buddy;s boat has the trs set I will swing by his boat to day and check it out ART
#3
Registered
Join Date: Nov 2003
Location: Melbourne, FL
Posts: 1,243
Likes: 0
Received 0 Likes
on
0 Posts
Re: cross post -- need help fast please
Here is a diagram of a closed colling system--shows cooler location for you.
Cooler(s) are between water pickup and raw water pump. Trans is connected to one of coolers (power steering is other one) and dumps thru the block/manifolds. I've got a pair of dual collers that are brand new -- make a great deal on them.
Cooler(s) are between water pickup and raw water pump. Trans is connected to one of coolers (power steering is other one) and dumps thru the block/manifolds. I've got a pair of dual collers that are brand new -- make a great deal on them.
Last edited by Poorsche; 06-03-2005 at 06:03 AM.
#4
Offshoreonly Advertiser
Offshoreonly Advertiser
Re: cross post -- need help fast please
The stock set up had a fitting in the drain plug on the brass bodied sea pump. That cooler does not need much water, it is only a 3/8 hose. So yes, T off the outlet of the sea pump, the origiial fitting was 1/8 npt (about a 1/4" ID).
__________________
Marc
www.mercruiserparts.com
www.go-fast.com
www.bammarine.com
www.cyborgtransmissions.com
It's not alive -www.BoatStuffExpress.com - temporarily retired
Marc
www.mercruiserparts.com
www.go-fast.com
www.bammarine.com
www.cyborgtransmissions.com
It's not alive -www.BoatStuffExpress.com - temporarily retired
#7
Offshoreonly Advertiser
Offshoreonly Advertiser
Re: cross post -- need help fast please
hi Mark, yep it is just not the same w/o Chicago.
Coming down any time soon?
Coming down any time soon?
__________________
Marc
www.mercruiserparts.com
www.go-fast.com
www.bammarine.com
www.cyborgtransmissions.com
It's not alive -www.BoatStuffExpress.com - temporarily retired
Marc
www.mercruiserparts.com
www.go-fast.com
www.bammarine.com
www.cyborgtransmissions.com
It's not alive -www.BoatStuffExpress.com - temporarily retired