alluminum vs. cast iron heads
#12
Registered
Join Date: Dec 2005
Location: Lanexa VA/St. Pete FL
Posts: 384
Likes: 0
Received 0 Likes
on
0 Posts
Re: alluminum vs. cast iron heads
If your looking for a good alum. head out of the box I Highly recommend the AFRs. If your looking to go bigger down the road & wanna do a lot of porting I suggest the Brodix. You will love having a set of alum heads, you will be able to tell a considerable difference. You mat also want to talk to an experienced BOAT motor builder, a good combo (heads, cam, rockers, intake, etc.etc.) is always better than just going BIG.
#13
Registered
Thread Starter
Join Date: Oct 2005
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
Re: alluminum vs. cast iron heads
Thanks for the post
Its not me building the engines. It's an engine builder with a lot of experience. I'm not a mechanic but do want to know as much as possible. He's given me choices and want to make an educated decision. Also if someone has done this combonation before their opinion would be great. Really don't want more power just more reliability. If i could squeak more hp reliably and drop boost that would seem to make sense...
Its not me building the engines. It's an engine builder with a lot of experience. I'm not a mechanic but do want to know as much as possible. He's given me choices and want to make an educated decision. Also if someone has done this combonation before their opinion would be great. Really don't want more power just more reliability. If i could squeak more hp reliably and drop boost that would seem to make sense...
Last edited by berman58; 01-10-2006 at 07:33 PM.
#14
Charter Member # 545
Gold Member
Re: alluminum vs. cast iron heads
I ran AFR aluminum heads on a set of whippled 540's with 7 LBS of boost. The motors have almost 350 hrs and have been in 2 different boats. No problem. Just match the intake runner size to cam you are using. AFR has a tech line, or their are a couple of dealers on the board. Mercury Marine uses Edlebrock Aluminum heads on the 600 SCI motors. With aluminum heads you could go with more compression safely. 8.5-9.0 on pump gas. Good luck.
#16
Registered
Re: alluminum vs. cast iron heads
Originally Posted by blastersbro
that combo sounds like junk who built it?
#17
Registered
VIP Member
Re: alluminum vs. cast iron heads
In my quest and thirst for more knowledge I have asked the same question to many different engine builders and here's what I've been told:
Aluminum heads dissipate heat faster, so you can have a little more compression without the detonation.
The negative aspect, of course, is the corrosion in salt water.
These are the only two factors that nobody I asked disagreed on!
Aluminum heads dissipate heat faster, so you can have a little more compression without the detonation.
The negative aspect, of course, is the corrosion in salt water.
These are the only two factors that nobody I asked disagreed on!
#18
Registered
Thread Starter
Join Date: Oct 2005
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
Re: alluminum vs. cast iron heads
Originally Posted by blastersbro
671 bds on a 540 is working too hard,creating extra intake heat.no one uses 7.5 compression because it will have no balls in no boost conditions.what else you got?
at 3500 rpm I have plenty of power, in a 1981 fully redone 39foot cigarette I run 58 mph and at 5800 run 86mph
#19
Registered
Re: alluminum vs. cast iron heads
aluminum head advantage:better port design,cnc porting available most brands,can run more compression with less chance of detonation,less weight,easier to repair, more power due to better port design.i use afr cnc ported on all my 540/565/572/598 engine combo great reliabity no problems.as far as corosion we hard coat anodize and recommend flushing with salt away i beleive they should last as long as cast iron.i am a dealer for afr have heads in stock .dave 410-956-5381. aluminum disadvantage more money
#20
Platinum Member
Platinum Member
Join Date: Sep 2002
Location: Millersville,MD
Posts: 381
Likes: 0
Received 0 Likes
on
0 Posts
Re: alluminum vs. cast iron heads
Originally Posted by MDGperformance
aluminum head advantage:better port design,cnc porting available most brands,can run more compression with less chance of detonation,less weight,easier to repair, more power due to better port design.i use afr cnc ported on all my 540/565/572/598 engine combo great reliabity no problems.as far as corosion we hard coat anodize and recommend flushing with salt away i beleive they should last as long as cast iron.i am a dealer for afr have heads in stock .dave 410-956-5381. aluminum disadvantage more money
What kind of longevity have you seen from the AFR's as far as hours run before valve job is needed? I know many people are having great success with these heads but I was curious if their exhaust seats are ground wide enough to last in a boat engine.
Thanx