who makes clamp on mufflers for 5" dry tails?
looking for non switchable exhaust that clamps on 5" tails and will not melt from running dry, has cmi released thier new run dry muffler? thx, rm
|
Re: who makes clamp on mufflers for 5" dry tails?
Originally Posted by ratman
looking for non switchable exhaust that clamps on 5" tails and will not melt from running dry, has cmi released thier new run dry muffler? thx, rm
|
Re: who makes clamp on mufflers for 5" dry tails?
I run 4 1/2" dry CMI's with GGB Extremes, no problems so far. They make them in 5" as well.
|
Re: who makes clamp on mufflers for 5" dry tails?
GGB is the only muffler that I'm aware of that will work with completely dry exhaust.
Fred@Trick |
Re: who makes clamp on mufflers for 5" dry tails?
fred do you have pics of the them? i thought i saw where you said cmi was almost ready to release thier new run dry design? thx, phil
|
Re: who makes clamp on mufflers for 5" dry tails?
I called CMI directly about two weeks ago... They're hoping for a late May release.
Neil |
Re: who makes clamp on mufflers for 5" dry tails?
thx
|
Re: who makes clamp on mufflers for 5" dry tails?
3 Attachment(s)
Here are a few pics of the GGB's. I don't have any pictures of them installed.
|
Re: who makes clamp on mufflers for 5" dry tails?
The pictured rubber flap will not last a minute at WOT on a truly "dry" exhaust.
|
Re: who makes clamp on mufflers for 5" dry tails?
If by dry you mean the CMI thruhull tails with the water slots on the end of the tailpipe, we have a muffler that will work. We do a race tail with internal water half couplings and a thru hull water dump for some applications.
|
Re: who makes clamp on mufflers for 5" dry tails?
Assuming the 5" dry exhaust is on a 1000+ hp engine. A lot of the mufflers I have looked at inlcuding those pictured choke the engine. 5" down to 3.5-4". Sort of defeats the whole system.
|
Re: who makes clamp on mufflers for 5" dry tails?
I have looked at inlcuding those pictured choke the engine. 5" down to 3.5-4". Sort of defeats the whole system. |
Re: who makes clamp on mufflers for 5" dry tails?
If by dry you mean the CMI thruhull tails with the water slots on the end of the tailpipe, we have a muffler that will work. We do a race tail with internal water half couplings and a thru hull water dump for some applications. |
Re: who makes clamp on mufflers for 5" dry tails?
were runnin triple 960hp bbc with stainless marine gen III w. 5in pipes on the revo we have been restoring, and ggbs were the only we could find, but instead of restricting the engine we decided to have stainless marine make flared turn downs for the 2 rear engines that run exhaust into the water, but once planned off, are no longer in water, and the center engine we had to run out the sides so we couldnt use mufflers or turn downs, so we just plan on not runnin the center untill away from public :drink:
|
Re: who makes clamp on mufflers for 5" dry tails?
1 Attachment(s)
Originally Posted by jrz
The pictured rubber flap will not last a minute at WOT on a truly "dry" exhaust.
The GGB's work well for my application. |
All times are GMT -5. The time now is 11:34 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.