KAAMA, Waterfoul, Dyno
 

Hey guys. I get out of work at 5 and plan on being at Super V's around 6. All I plan on doing tonight is getting the blocks on the stands and getting things organized for the assembly.

Ok..when can I show up and show you guy's how to really put those bad boys together ;) :D

have fun boys....sounds like MONDAY NIGHT MAYHEM in the garage :cool:

[ 01-08-2002: Message edited by: traviss ]

Crazy, email me the address please.

I think you and Wade can handle that without me....I'll come down when you start assembling....

Dyno, you wuss. Don't wanna do the grunt work, just the fun stuff. I'll save the intakes for ya to scrape. :D :D

Can't make it tonight Dave. Gotta call Flylevel and run out to visit my boat.

KAAMA, call my cel, 403-3962.

Good to see you yesterday KAAMA. Got anything going Thursday evening? How long did you after I left?

[ 01-09-2002: Message edited by: Crazyhorse ]

Dave, i was there for maybe 5 minutes after you left...nice people. I just might show up on Thursday night.

Ok. I'll figure on being there Thurs. night. I can clean head bolts and oil pans. Waterfoul, are you available? If I don't have to work Saturday I'll probably do a bottom end on engine #1. KAAMA, did yu contact that guy we talked about?

[ 01-10-2002: Message edited by: Crazyhorse ]

Crazy, yeah I talked to him...nice fella. I will talk more about it with you tonight.

Super V's shop isn't far from the Riverview airport. Maybe a short hop in a four-seat Cherokee? Waterfoul, you listening?

KAAMA, good to see you last night. I'll be at Super V's Saturday morning after I meet a guy at Rainbow Grill for coffee at 8 am.I'm planning on getting engine #1 assembled.

So, rainbow grill at 8:00 then?? Got room for another Dave? And, if possible I would like to pick up that cherry picker Saturday too, my motor is being pulled on Sunday!!! I tried to call you after work tonight. No answer. Gimme a call on the cell.

W.F., unfortunately I didn't get home until now. Give me a call in the morning and I'll be at Super V's shop where you can pick up the picker and bring me coffee. :D :D

Hey Crazyhorse, is SuperV's shop in G-ville? You Fly out of Jenison?

Super V's shop is slightly southeast of Hudsonville. Yes, I fly out of Riverview. I'm thinking about going up tomorrow if the weather isn't too crappy. I only need 900 foot ceilings to go play.

[ 01-11-2002: Message edited by: Crazyhorse ]

Southeast of Hudsonville sounds a lot like Jamestown. That's were I'll be tommorrow morning, pulling an engine. Good luck w/ the weather. How're the engines coming along?

I'll get one together tomorrow. Super V's place is close to where 22nd Street crosses Barry St. You yanking your motor? Or helping someone else?

Sounds like SuperV might be in the produce business. I'm pulling a Cherokee motor in the morning and hoping to pull my boat motor in the afternoon if a friend of mine is available so I can use the overhead hoist in his shop. Did you tell me an 850 Holley would be too big for a 454? What about a World Products single plane intake?

I like the 850 on the 454's. I prefer the dual-plane intake because it makes more low and midrange power than the single-plane intakes (longer runners). Dyno has dual-plane, Super V has single-plane. Otherwise they have about the same engines. Don't be fooled by the volumetric efficiency calculations. Marine engines can run over 100 percent VE. I'm going to bed. Call me tomorrow if you get a chance. 403-3962.

BGIII I ran both a single plane and a dual plane on my roller 502 and liked the dual better.....sold the single to JimV, he might still have it...it is an oval port my motor didnt turn over 5200 so the single plane did'nt help any and I lost some bottom end.
my.02