Bolt on swim platform
Anybody have any suggestions on a company that makes after market swim platforms? thanks for the help
|
try this hope it helps
http://www.westcoastoffshoreunlimite...-platform.html |
I checked them out, is it always $2,500.00 + - for welded aluminum and some powder coating? A buddy of mine makes aluminum items and powdercoats them. He says based on the raw material needed and the powdercoating + labor, he estimates a max cost of $650 to $750. Seems like a lot of profit even if he is way off:(......
|
yeah - that site is out of control. I called for a quote on mine last year ans they wantes 3700. - I told them to beat it.
|
I do not recall if it was in the LOTO/Midwest boating forum here or on Midwestboatparty.com, a member had one made just in the last few months by a local shop at LOTO for just over $1000.00 Take a look, it seems a lot more feasible than $3k.
|
|
check with Eddie marine,
got a powdercoated alum with boat manufacturer engraved into the platform for $1800 |
these guys do good work
http://www.topsntowers.com/ |
I talked to Westcoast the other day. Their price for my 7' wide boat was $2350 + $295 for a ladder + $200 shipping. Their part looks nice, but I don't know that I want to spend that much. I think I may take some measurements off the back of my boat, and draw one up in cad and see if I can't get someone local to make it. Who knows, that would probably be more expensive in the end!
|
Originally Posted by Dave M
(Post 2506893)
Dave, you don't still have your measurements from when you bought yours do you? |
Originally Posted by jayhawk261
(Post 2506937)
Dave, you don't still have your measurements from when you bought yours do you?
These are the specs I mailed to Extreme and it fit like a glove. Yours should be the same except for your tabs. I don't know if the are the same brand and location. Exhaust Pipe Diam: 4 Inch Exhaust Flange Diam: 1 Inch Type of Drive: Mercruiser Bravo 1 Transom Angle: ?? External Steering: Mayfair Single Ram Lifting Eyes: 2, See Picture A: Width of Transom at Top, 73.25 inches B: Center to center, 27.5 inches F: Rub rail to keel, 17.5 inches H: Bottom of rub rail to center, 2.5 inches I: Bottom of rub rail to gimbal, 5.5 inches J: width of transom at bottom 69 inches U: 15 inches V: 20.25 inches W: 26.75 inches X: 10 inches Y: 12 inches Z: 15 inches Color Choice: RAL 3001 |
Thanks Dave!
|
Thanks for the suggestions I will check them out.
|
Originally Posted by hammer01
(Post 2506870)
I do not recall if it was in the LOTO/Midwest boating forum here or on Midwestboatparty.com, a member had one made just in the last few months by a local shop at LOTO for just over $1000.00 Take a look, it seems a lot more feasible than $3k.
|
Jim Kruse Powdercoating at LOTO made mine last Fall. It was $1600 installed. He will most likely need the boat to make it unless you can use one of teh standard versions he has a jig for.
http://www.offshoreonly.com/forums/s...d.php?t=181516 |
1 Attachment(s)
this one was 2500. as an option from Nortech, I had it painted to match and non skid applied as well...best and safest thing Ive ever done on a boat. It covers the drives completely and makes it easier boarding, one step up to the fiberglass step and then one more to sunpad..Good Luck Jeff
|
Originally Posted by Griff
(Post 2508096)
Jim Kruse Powdercoating at LOTO made mine last Fall. It was $1600 installed. He will most likely need the boat to make it unless you can use one of teh standard versions he has a jig for.
http://www.offshoreonly.com/forums/s...d.php?t=181516 Thanks! |
All times are GMT -5. The time now is 06:15 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.