Offshoreonly.com
Page 3 of 3
1
2
3
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   General Boating Discussion (https://www.offshoreonly.com/forums/general-boating-discussion-51/)
-   -   Single engine V - NXT drive? (https://www.offshoreonly.com/forums/general-boating-discussion/204901-single-engine-v-nxt-drive.html)

Magic Medicine 03-18-2009 03:18 PM
Originally Posted by CB-BLR (Post 2823809)
Talk about a sleeper....
I bet it is paid for.

:grinser010:

Chris
I sure hope so, sorry I couldn't resist:evilb:

masher44 03-19-2009 12:38 AM
Originally Posted by realityslap (Post 2823963)
Adrenaline built a V30 with a 700/NXT package than ran about 95 and handled very well.
I assume it is a right hand rotation? Taking a right hand turn with a single right hand rotating prop can be very very very very hairy if you dont let off :eek:

What size prop?

tomtbone1993 03-19-2009 12:41 AM
Originally Posted by masher44 (Post 2824398)
I assume it is a right hand rotation? Taking a right hand turn with a single right hand rotating prop can be very very very very hairy if you dont let off :eek:
just exactly how very is very very very very hairy???

:evilb::evilb::evilb:

Bad Influence 03-19-2009 05:45 AM
Originally Posted by Oh Deere (Post 2823250)
... so we had a slight wedge welded on the skeg to counter the torque(which was not that bad)
Oh Deere,

do you have a picture for me how you welded this wedge on the skeg?

Iīve also an single application with NXT1.
Itīs an 30 Activator with EU662SCi without this "new" lower.
If I ran WOT I feel a lot of torque moving the boat to right.
btw: looking also for the "right" prop.

BI

Oh Deere 03-19-2009 08:31 AM
2 Attachment(s)
Hopefully you can see from these pictures. The wedge is only about 5 " high, and goes from @ 3/8 " thick to 0 over in 2.5" or so. You may be able to come up with one that is more efficient though. I will see if I can get at the boat today for a better picture.

Bad Influence 03-19-2009 09:22 AM
Oh Deere,

thx for quick response.
Picīs are perfect.
Understood, only to be sure,
youīre spinning an RH prop, right?

BI

masher44 03-19-2009 10:00 AM
Originally Posted by Bad Influence (Post 2824411)
Oh Deere,

do you have a picture for me how you welded this wedge on the skeg?

Iīve also an single application with NXT1.
Itīs an 30 Activator with EU662SCi without this "new" lower.
If I ran WOT I feel a lot of torque moving the boat to right.
btw: looking also for the "right" prop.

BI
what size prop you looking for? what have you tried?

masher44 03-19-2009 10:02 AM
Originally Posted by tomtbone1993 (Post 2824401)
just exactly how very is very very very very hairy???

:evilb::evilb::evilb:
stain your shorts very

Oh Deere 03-19-2009 10:31 AM
Originally Posted by Bad Influence (Post 2824506)
Oh Deere,

thx for quick response.
Picīs are perfect.
Understood, only to be sure,
youīre spinning an RH prop, right?

BI
Right hand rotation.

Bad Influence 03-20-2009 01:37 AM
Originally Posted by masher44 (Post 2824534)
what size prop you looking for? what have you tried?
My idea is Mercury Racing CNC 5 blade 16 x 31 (18 rake),
but I couldīt find one for testing.

I tested some Maximus props

Here my results:


> 15 1/4" x 28 Maximus (lab) Rev. Limiter (5450) 82mls
> 15 1/4" x 32 Maximus (lab) Rev.Limiter 89 mls
> 15 5/8" x 31 Maximus (lab) Rev.Limiter 89 mls
> 15 1/4" x 34 Maximus (lab) 4600 83mls

BI


All times are GMT -5. The time now is 12:57 PM.
Page 3 of 3
1
2
3
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.