What to expect out of a 496 CI
#1
Registered
Thread Starter
iTrader: (7)
What to expect out of a 496 CI
Just wondering what respectable but yet conservative number you can get out of a 496. I have been contiplating on stroking my 454's. I have always been able to achieve pretty good numbers and reliability from 454 rebuilds in the past however I was thinking of taking them to the next level. Reaching near 530 ft pds of trq and 500 HP at 5500rpm with 454/468's.
What would you think to expect with a 496 without going crazy. I'm ready to hang my rods and pistons to complete the short block and then I had a brain fart.
Any help with the project would be great so I can get moving here.
thanks,
John
What would you think to expect with a 496 without going crazy. I'm ready to hang my rods and pistons to complete the short block and then I had a brain fart.
Any help with the project would be great so I can get moving here.
thanks,
John
#5
Registered
iTrader: (1)
It all depends. What exhaust, heads, cam, intake. The only thing I would do different when I built mine was different heads. I used Edelbrock 290cc. Other than that I spared no expense best of everything. Like said above, just adding 42 cubic inches I would be surprised to see 50hp.
It reminds me of my first V8 boating engine I built, swamped the 305 228HP to a built 350. That shows my age
It reminds me of my first V8 boating engine I built, swamped the 305 228HP to a built 350. That shows my age
#6
Registered
Thread Starter
iTrader: (7)
RE: 454 upgrades
Thanks for the reply.
new question is:
with all the proper engine components such as solid bottom end, recommended intake - dart?, Perf. RPM Airgap?, holley 800 cfm., Say something similar to the 168731 cam - rmbuilder spec., Roller rockers, 9.5 to 1 comp. and gill exhaust. Parts for a 496 what to expect on the conserv. side as far as trq. and HP.
new question is:
with all the proper engine components such as solid bottom end, recommended intake - dart?, Perf. RPM Airgap?, holley 800 cfm., Say something similar to the 168731 cam - rmbuilder spec., Roller rockers, 9.5 to 1 comp. and gill exhaust. Parts for a 496 what to expect on the conserv. side as far as trq. and HP.
#7
Registered
Thread Starter
iTrader: (7)
The heads being used at this time are the worked over 049 casting's oval port 2.19's and 1.85's by Valako. We get these things to flow well and considering were under 500 CI and staying under 610 to 615 lift they will work fine. I used many of the dart recs and use to wedge them at this CI. Trq. and dyno results are amazing.
This is kind of a quick fix for this year. Next year I have decided to go to the 572's
This is kind of a quick fix for this year. Next year I have decided to go to the 572's
Last edited by getrdunn; 03-31-2009 at 10:12 PM.
#8
Registered
Just wondering what respectable but yet conservative number you can get out of a 496. I have been contiplating on stroking my 454's. I have always been able to achieve pretty good numbers and reliability from 454 rebuilds in the past however I was thinking of taking them to the next level. Reaching near 530 ft pds of trq and 500 HP at 5500rpm with 454/468's.
What would you think to expect with a 496 without going crazy. I'm ready to hang my rods and pistons to complete the short block and then I had a brain fart.
Any help with the project would be great so I can get moving here.
thanks,
John
What would you think to expect with a 496 without going crazy. I'm ready to hang my rods and pistons to complete the short block and then I had a brain fart.
Any help with the project would be great so I can get moving here.
thanks,
John
Without going crazy and having a reliable piece that can run on pump gas, you can expect about 1.20 hp/ci with aluminum heads and about 9.5:1 compression. With a little more compression and a decent size cam, you could expect to see 1.27-1.29 hp/ci. Hope this helps, Eddie
#9
Registered
iTrader: (3)
Without going crazy and having a reliable piece that can run on pump gas, you can expect about 1.20 hp/ci with aluminum heads and about 9.5:1 compression. With a little more compression and a decent size cam, you could expect to see 1.27-1.29 hp/ci. Hope this helps, Eddie
#10
Charter Member # 55
Charter Member
The heads being used at this time are the worked over 049 casting's oval port 2.19's and 1.85's by Valako. We get these things to flow well and considering were under 500 CI and staying under 610 to 615 lift they will work fine. I used many of the dart recs and use to wedge them at this CI. Trq. and dyno results are amazing.
This is kind of a quick fix for this year. Next year I have decided to go to the 572's
This is kind of a quick fix for this year. Next year I have decided to go to the 572's