|
Sea Strainer recommendations....
Well after my overheating problems with the seaweed, im thinking a sea strainer wouldnt be a bad option.
Is there any recommendations for my setup? 94 Baja 272 w/ 330hp Merc 454 and Bravo drive. Thanks! Pros and cons of different models would be great, as I have never used a strainer before. |
1 Attachment(s)
I have Marine Machine strainers - they seem to be a REAL nice piece....
|
Originally Posted by seafordguy
(Post 2877529)
I have Marine Machine strainers - they seem to be a REAL nice piece....
|
STAINLESS MARINE ,,,,, nothing else ,,TOP OF THE LINE !!!!!!!!!!
|
Originally Posted by daredevil
(Post 2877579)
STAINLESS MARINE ,,,,, nothing else ,,TOP OF THE LINE !!!!!!!!!!
|
Originally Posted by c_deezy
(Post 2877562)
Are those the ones with the aluminum tops and the stainless can? If so have you had any issues with the tops galling?
I haven't had any problems with them at all - look brand new. |
1 Attachment(s)
Get something you don't need a tool to open. I got those for the MTI...
Hardin marine bought them through Keith Eickert Marine http://www.keitheickert.com/images/620-913206.jpg http://www.keitheickert.com/detail.aspx?ID=8918 |
My boat was built with Marine Machine strainers. They are very solidly built units and I'd recommend them in a heartbeat. My years of experience with them tells me that it is critical to use a lot of anti-seize on the lids to prevent them from seizing up given that the buckets are Stainless and the lids are Aluminum. There have been threads here with some ugly pics of lids needing to be cut off. I had to cut mine off about 3-4 years ago. I had the lids off to clean them out and wiped off what I felt to be excess anti-sieze off the threads. Then I hosed down the bilge to clean it. The open spaces between the vanes on the lids trapped water which seeped down the threads and they seized up. Had to remove them which was awful in my boat and used a die grinder to carefully make two cuts in the edges of the lids to get them off. No problems since because I make darn sure I goop them up real good. This was entirely my fault. For what its worth....
|
Originally Posted by GLH
(Post 2877642)
Get something you don't need a tool to open.
Originally Posted by Lmarth
(Post 2877671)
My boat was built with Marine Machine strainers. They are very solidly built units and I'd recommend them in a heartbeat. My years of experience with them tells me that it is critical to use a lot of anti-seize on the lids to prevent them from seizing up given that the buckets are Stainless and the lids are Aluminum. There have been threads here with some ugly pics of lids needing to be cut off. I had to cut mine off about 3-4 years ago. I had the lids off to clean them out and wiped off what I felt to be excess anti-sieze off the threads. Then I hosed down the bilge to clean it. The open spaces between the vanes on the lids trapped water which seeped down the threads and they seized up. Had to remove them which was awful in my boat and used a die grinder to carefully make two cuts in the edges of the lids to get them off. No problems since because I make darn sure I goop them up real good. This was entirely my fault. For what its worth....
|
Im happy with the livorsi unit as well.
http://www.livorsi.com/catalog/sea_strainers.htm
Very happy with my Livorsi sea strainer. Definitely get one you dont need tools to open. Chasing sockets and wing nuts in a dirty bilge is a bummer when your trying to get back underway. Cant imagine boating without a sea strainer anywhere- there is so much crap everywhere these days. Lakes, ocean kelp beds it all ends up in there. Uncle Dave |
| All times are GMT -5. The time now is 01:30 AM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.