volvo vs bravo
#11
Registered
You can't go fast enough with the standard gear ratio's (1.5) @3,900 engine rpm's for there to be any noticable difference in speed or performance between the two drives.
#12
Registered
Join Date: Aug 2009
Posts: 89
Likes: 0
Received 0 Likes
on
0 Posts
@SCOT BB;
MSA need service each 300 working hours (It mean oil change and nothing else), except bigg rubber pipe from transom seal kit which is from Mercruyser!
Two years ago I am have chance to test this drive:
Same boat typ with 2 steps, 4.200 pounds empty weight and with originall 496 HO engines.
- One boat with BravoX with 2 inch higher cavitation plate, bravo 1 prop.
- Second with MSA drive and maximus prop.
- Start by Bravo it was like each start. Bow up, brrrrr and slow acceleration
- with MSAit is like by dragster cars with out of any bow lift! It have speciall chanal for air which vented prop for better start.
- End speed with Bravo1X it was 69 mph.
- with MSA 79 mph until revolution blockade of engine. In my oppinion it is end speed of this combination round of 81-82 mph.!
Two days after test I am buy MSA drive and I do not care if it is first service 800 km from me. So what if have no troubles with it. It look bad yes, but who care, it is under water. And efficiency it is incredible better than by any Z drives.
MSA it is wonderfully drive if you need efficiency and it never blow out. This is surface drive with tunnel effect and you could use standard inox props like Bravo1 or Maximus.
Bigg diference in comparison with for example Arneson it is lot of trim effect and less chine walk of boat.
I do not know what meaning have this in USA, but it is reall quality maded Germany product.
When you install it, you do not need to take care round of X dimension like by Z drives. You only mount it like it is writen in papers and rest make trim.
p.s.
Sorry for my bad english, but I hope that you understand what I am want to tell.
bye
Saso
MSA need service each 300 working hours (It mean oil change and nothing else), except bigg rubber pipe from transom seal kit which is from Mercruyser!
Two years ago I am have chance to test this drive:
Same boat typ with 2 steps, 4.200 pounds empty weight and with originall 496 HO engines.
- One boat with BravoX with 2 inch higher cavitation plate, bravo 1 prop.
- Second with MSA drive and maximus prop.
- Start by Bravo it was like each start. Bow up, brrrrr and slow acceleration
- with MSAit is like by dragster cars with out of any bow lift! It have speciall chanal for air which vented prop for better start.
- End speed with Bravo1X it was 69 mph.
- with MSA 79 mph until revolution blockade of engine. In my oppinion it is end speed of this combination round of 81-82 mph.!
Two days after test I am buy MSA drive and I do not care if it is first service 800 km from me. So what if have no troubles with it. It look bad yes, but who care, it is under water. And efficiency it is incredible better than by any Z drives.
MSA it is wonderfully drive if you need efficiency and it never blow out. This is surface drive with tunnel effect and you could use standard inox props like Bravo1 or Maximus.
Bigg diference in comparison with for example Arneson it is lot of trim effect and less chine walk of boat.
I do not know what meaning have this in USA, but it is reall quality maded Germany product.
When you install it, you do not need to take care round of X dimension like by Z drives. You only mount it like it is writen in papers and rest make trim.
p.s.
Sorry for my bad english, but I hope that you understand what I am want to tell.
bye
Saso
Last edited by sinus; 02-18-2010 at 06:14 AM.
#14
arneson-industries.com
Offshoreonly Advertiser
Just buy an Arneson Surface Drive.
Problem solved!
Problem solved!
__________________
Arneson Surface Drives www.arneson-industries.com
Arneson Surface Drives www.arneson-industries.com
#16
English translation
£ = $$ (at today's exchange rate)
but
Bravo ≠ Arneson asd8
in fact . . . . Bravo × Bravo × Bravo is still not = asd8 . . . (or Bravo^3<asd8) . . so the math kinda works in favor of the Arneson after the variables work themselves out. . . . . . You'll only buy one Arneson and they are well suited to this application.
£ = $$ (at today's exchange rate)
but
Bravo ≠ Arneson asd8
in fact . . . . Bravo × Bravo × Bravo is still not = asd8 . . . (or Bravo^3<asd8) . . so the math kinda works in favor of the Arneson after the variables work themselves out. . . . . . You'll only buy one Arneson and they are well suited to this application.
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
Last edited by glassdave; 02-18-2010 at 04:15 PM.
#17
Platinum Member
Platinum Member
#18
Registered
Thread Starter
Join Date: Dec 2007
Posts: 187
Likes: 0
Received 0 Likes
on
0 Posts
i know what your sayin is right tho a asd 8 would be out of my budget right now
if i could only afford an asd 8 i would put it on my 440 yanmar diesel
maby rik will take installments and have his drive promoted in ireland
if i could only afford an asd 8 i would put it on my 440 yanmar diesel
maby rik will take installments and have his drive promoted in ireland
#19
arneson-industries.com
Offshoreonly Advertiser
What, a little over 10K £ and one hell of a lot of value there. that German thing is........
__________________
Arneson Surface Drives www.arneson-industries.com
Arneson Surface Drives www.arneson-industries.com
#20
Platinum Member
Platinum Member