Go Back  Offshoreonly.com > General Discussion > General Boating Discussion
Technical Questions For Steve 1 >

Technical Questions For Steve 1

Notices

Technical Questions For Steve 1

Thread Tools
 
Old 06-21-2010, 04:57 PM
  #101  
Neno the mind boggler
VIP Member
iTrader: (1)
 
glassdave's Avatar
 
Join Date: Sep 2001
Location: toledo oh
Posts: 13,069
Received 271 Likes on 96 Posts
Default

Originally Posted by Steve 1
Good Eye Dave, when I did the math models at 1200# VS the 15-18 degrees found in 5000# Hulls I came up with something a "little" different in deadrise also a byproduct of the radical bottom clean up was My stuff is able run in the rough and not beat up the crew.Look at a Cheetahcat run it does not create much of a disturbance at high speed everything is on the pads. the second boat I sent to Kuwait they were leading a very rough race and the boat trying to run second behind them crashed killing some people and the race was black flagged. the deadrise allows it to sink just enough in the wave crest to allow a straight path,If you are going up or down the boat is not going forward very fast.

On the M-11 Vid look at the beginning and watch it travel through the pack of M Boats.Watch the first 50 seconds for the cheetahcat then the pads and deadrise will be better explained.

http://www.youtube.com/watch?v=esxxt...eature=related

Drat they disabled my Chili Peppers Aeroplane
makes sense to me. I always thought using a delta pad can give you some speed but at the cost of a harsher ride. Buy coupling it with a steeper deadrise you can restore some of that, so theres is a balance between the two. This was something you found in the math beforehand? So through design you dont necessarily need a heavy boat to tame rough water.


Damn youtube police
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
glassdave is offline  
Old 06-21-2010, 05:49 PM
  #102  
Platinum Member
Platinum Member
 
Steve 1's Avatar
 
Join Date: Apr 2001
Location: Beautiful Fort Lauderdale www.cheetahcat.com
Posts: 10,833
Likes: 0
Received 6 Likes on 6 Posts
Default

Originally Posted by glassdave
makes sense to me. I always thought using a delta pad can give you some speed but at the cost of a harsher ride. Buy coupling it with a steeper deadrise you can restore some of that, so theres is a balance between the two. This was something you found in the math beforehand? So through design you dont necessarily need a heavy boat to tame rough water.


Damn youtube police
Exactly and that engineered ride will not ever beat you ,The fishing boats also were very well mannered all the way from idle through "Boat" mode and into warp speed very predictable. LMAO it was a cool bit of background music.
Steve 1 is offline  
Old 06-21-2010, 08:59 PM
  #103  
Platinum Member
Platinum Member
 
Steve 1's Avatar
 
Join Date: Apr 2001
Location: Beautiful Fort Lauderdale www.cheetahcat.com
Posts: 10,833
Likes: 0
Received 6 Likes on 6 Posts
Default

Dave I will work on the music the next couple days.
Steve 1 is offline  
Old 06-21-2010, 09:42 PM
  #104  
Shoot'n Motion @ 1/80 Sec
Commercial Member
 
Eaton Photos's Avatar
 
Join Date: May 2009
Location: Louisville, Ky.
Posts: 456
Likes: 0
Received 6 Likes on 6 Posts
Default

From a Technical standpoint, I honestly do not understand some of the key terms & phrases being used in this thread, but beyond those points, I've learned more from reading the past 10 pages, than I have read anywhere else online.

The knowledge & experiences that Steve has been sharing, is amazing.
__________________
James Eaton
www.eatonphotos.com
Eaton Photography on Facebook
Eaton Photos is offline  
Old 06-21-2010, 10:19 PM
  #105  
Platinum Member
Platinum Member
 
Steve 1's Avatar
 
Join Date: Apr 2001
Location: Beautiful Fort Lauderdale www.cheetahcat.com
Posts: 10,833
Likes: 0
Received 6 Likes on 6 Posts
Default

Originally Posted by Eaton Photos
From a Technical standpoint, I honestly do not understand some of the key terms & phrases being used in this thread, but beyond those points, I've learned more from reading the past 10 pages, than I have read anywhere else online.

The knowledge & experiences that Steve has been sharing, is amazing.
Sir stop me anytime and I will break it down a little further and I thank you for the nice comment.
Steve 1 is offline  
Old 06-21-2010, 10:44 PM
  #106  
Registered
 
Join Date: Aug 2007
Location: Chesapeake Bay
Posts: 144
Likes: 0
Received 0 Likes on 0 Posts
Default

Steve, I cannot begin to tell you how much I am learning from this thread.

Thank you very much!

James
Apathetic is offline  
Old 06-21-2010, 10:47 PM
  #107  
Platinum Member
Platinum Member
 
Steve 1's Avatar
 
Join Date: Apr 2001
Location: Beautiful Fort Lauderdale www.cheetahcat.com
Posts: 10,833
Likes: 0
Received 6 Likes on 6 Posts
Default

Originally Posted by Apathetic
Steve, I cannot begin to tell you how much I am learning from this thread.

Thank you very much!

James
I humbly thank you for the nice comments.
Steve 1 is offline  
Old 06-21-2010, 11:04 PM
  #108  
Registered
 
Join Date: Oct 2005
Location: LI, New York
Posts: 1,491
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by Steve 1
Sir stop me anytime and I will break it down a little further and I thank you for the nice comment.
What's a delta pad?
Mastercraft240 is offline  
Old 06-21-2010, 11:42 PM
  #109  
Platinum Member
Platinum Member
 
Steve 1's Avatar
 
Join Date: Apr 2001
Location: Beautiful Fort Lauderdale www.cheetahcat.com
Posts: 10,833
Likes: 0
Received 6 Likes on 6 Posts
Default

Originally Posted by mastercraft240
What's a delta pad?
Sir the pad would start narrow then widen at the transom, Kind of a triangle shape.
Steve 1 is offline  
Old 06-22-2010, 10:05 AM
  #110  
Platinum Member
Platinum Member
 
Steve 1's Avatar
 
Join Date: Apr 2001
Location: Beautiful Fort Lauderdale www.cheetahcat.com
Posts: 10,833
Likes: 0
Received 6 Likes on 6 Posts
Default

Dave here is the Pad on a old Cheetahcat 40.


Steve 1 is offline  


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.