Notices

PSD drive train questions

Old 06-24-2002, 06:50 PM
  #1  
Registered
Thread Starter
 
Join Date: Aug 2001
Location: Indy, St. Louis, LOTO
Posts: 1,333
Likes: 0
Received 1 Like on 1 Post
Default PSD drive train questions

Is there a simple way to determine final gear ratio in a used PSD?

For example, with stock size tires, XXXX RPMs at YY MPH equals Z.ZZ drive ratio.



Secondarly, is a shorter ratio harder on the drive train than a taller ratio? (I've thought about this, and can think of good arguments for both sides).

Thanx.
Chart is offline  
Old 06-26-2002, 12:50 PM
  #2  
Registered
Thread Starter
 
Join Date: Aug 2001
Location: Indy, St. Louis, LOTO
Posts: 1,333
Likes: 0
Received 1 Like on 1 Post
Default

ttt
Chart is offline  
Old 06-26-2002, 12:57 PM
  #3  
Registered
 
SeaDated's Avatar
 
Join Date: Mar 2001
Location: Kennesaw, GA, USA
Posts: 854
Received 0 Likes on 0 Posts
Default

Try thisrive Train

Final Drive Ratio Computation


The formula is:

Final ratio = (Tire Diameter in Inches x RPM) / (336 x MPH)
SeaDated is offline  
Old 06-26-2002, 01:39 PM
  #4  
Registered
 
ccarloss's Avatar
 
Join Date: May 2002
Location: Pasadena, MD
Posts: 279
Received 0 Likes on 0 Posts
Default

2000 PSD 4X4 automatic w/3:73 rear turns approx 2050RPM's at 70MPH with 265/75/16 tires.

I believe the 4:10's turn about 2300-2350 @ 70MPH
ccarloss is offline  
Old 06-26-2002, 01:44 PM
  #5  
Registered
Thread Starter
 
Join Date: Aug 2001
Location: Indy, St. Louis, LOTO
Posts: 1,333
Likes: 0
Received 1 Like on 1 Post
Default

Thanks guys.


Does the drive train have more stress (likelyhood of breaking) with the shorter ratio than the taller ratio, pulling a load?
Chart is offline  
Old 06-26-2002, 01:56 PM
  #6  
Charter Member #232
Charter Member
 
Audiofn's Avatar
 
Join Date: Oct 2000
Location: Carlisle, MA USA
Posts: 18,422
Received 6 Likes on 4 Posts
Default

You can take the Vin # and call the dealer they will be able to tell ya from that. What is your concern? I think that your boat is not going to put any stress on that truck what so ever. I pull mine and I keep looking back to see if it is still there. Curts Cig that was substantially heavier then our 302's you could tell was back there but it would hold 70-75 no problem and averaged about 12-13mpg all the way home
__________________
Put your best foot forward!
Audiofn is offline  
Old 06-26-2002, 03:09 PM
  #7  
Registered
Thread Starter
 
Join Date: Aug 2001
Location: Indy, St. Louis, LOTO
Posts: 1,333
Likes: 0
Received 1 Like on 1 Post
Default

Jon: Concern is a strong word; it is more an interest. After using what little gray matter I have on a ponder, I hate to leave it unresolved. Our 10-12,000 lb loads wont challenge either one, heck I pull it now with a stock-drivetrain half-ton burban. (Yes, the breaks and suspension are beefed up on it).

So, do the individial teeth on the gears in a drive train have more stress applied with a short final ratio than a tall ratio, or is it the same.

After all the time we spent on "which freezes faster: hot or cold water?", there should be some good insight on the gear question.
Chart is offline  
Old 06-26-2002, 06:00 PM
  #8  
Charter Member #232
Charter Member
 
Audiofn's Avatar
 
Join Date: Oct 2000
Location: Carlisle, MA USA
Posts: 18,422
Received 6 Likes on 4 Posts
Default

I am going to say that there is less stress on the drive trail with shorter gears. IE causing your RPM's to be higher on the highway. The axle I would think is under more stress however.

Jon
__________________
Put your best foot forward!
Audiofn is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
long duck dong
Drives and Lower Units
6
11-24-2007 06:35 PM
hpy540
General Q & A
0
07-27-2007 12:13 PM
FormulaM2Formula
Formula
4
06-11-2006 01:19 PM
Raypanic
General Q & A
5
06-10-2003 11:38 AM
tomcat
General Q & A
1
01-25-2002 11:21 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Quick Reply: PSD drive train questions


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.