Show us your garages/shops!
#31
Guest
Posts: n/a
You asked for it
Here it is. 400 square feet of insulated manufacturing and engine building space. Complete with 5000 watts of electric heat to keep it at 40 degrees in the winter, 2500 cfm dust collection system. Along with a kerosene heater to get it to 70 so its comfortable so the cost of electric doesn't kill me. Eletric is 100 amp service from the house with 220 for the saw, compressor, heat and dust collector. On the other side of the saw is about 1000 board feet of oak, walnut and cherry to take up even more space.
Believe it or not, I built 2 engines and ported 4 heads at the same time in here while running my wood working business. In the back ground there are 3 pieces in progress for a woman in Cocoa Florida that is putting them in a national magazine. I also share the space with a 28 inch snow blower, kids electric jeep and tractor. I need more room!! But then I would just fill it up with more stuff.
Believe it or not, I built 2 engines and ported 4 heads at the same time in here while running my wood working business. In the back ground there are 3 pieces in progress for a woman in Cocoa Florida that is putting them in a national magazine. I also share the space with a 28 inch snow blower, kids electric jeep and tractor. I need more room!! But then I would just fill it up with more stuff.
#34
Registered
Join Date: Oct 2000
Location: Austin, TX
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
28'x30' with 9' minimum clearance inside, 10' overhead door, epoxy floor. The boat sits outside until someone want to come buy it from me...
...friggin picture's too big and I don't feel like messing with it...
Workbenches and worktable, Delta Unisaw, 14" bandsaw, oxy/acetylene, MIG, TIG, BIG Snap-On toolbox, 6hp/60gallon compressor, lot's of lights, lot's of power 120/240
...OK, I messed with the picture... ...still didn't work...
...still messing with it...
...friggin picture's too big and I don't feel like messing with it...
Workbenches and worktable, Delta Unisaw, 14" bandsaw, oxy/acetylene, MIG, TIG, BIG Snap-On toolbox, 6hp/60gallon compressor, lot's of lights, lot's of power 120/240
...OK, I messed with the picture... ...still didn't work...
...still messing with it...
#35
Registered
Join Date: Oct 2000
Location: Austin, TX
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
Inside shot just before the big "Might as well Spill the Beer on the New Floor Since it Failed the City's Final Inspection Party". The bikes now sit in the front garage, out of the way of projects...
Last edited by JohnJan; 12-17-2002 at 04:53 PM.
#40
Platinum Member
Platinum Member
Join Date: Jun 2001
Location: Cold Spring, Ky./Cape Coral,Fl.
Posts: 453
Likes: 0
Received 0 Likes
on
0 Posts
Ok guys: I guess I got the utimate garage . Morton building 48widex105long concrete floor 6 inches of insulation 14feet of height. air-conditioning ,full bathroom satellite tv. full bar desk for computer all of this to house the following toys. 99 38' PQ avenger, 5320 Jd tractor 4500 jd tractor one gator, 1984 Monte Carlo, 1987 Monte Carlo Show cars. 2001 Corvette. O and one last thing. I build this just so I had a place to house the Mistress when ever I want to play around. The tv couch turns into a bed. The guy with the most toys wins. Wildman 1 aka Blondes Preferred