Go Back  Offshoreonly.com > General Discussion > General Boating Discussion
Dug into my motor tonight.......good news!!! >

Dug into my motor tonight.......good news!!!

Notices

Dug into my motor tonight.......good news!!!

Thread Tools
 
Old 09-03-2002, 10:17 PM
  #1  
Gone Fishin'
Charter Member
Thread Starter
 
Waterfoul's Avatar
 
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes on 0 Posts
Default Dug into my motor tonight.......good news!!!

Well, I tore the intake manifold off after sucking up a LOT of sand this past Sunday. When I backflushed the system on the water with a funnel and bucket, I spilled some water on the intake and saw bubbles coming up thru the water between the intake and the port head. So I replaced both intake gaskets tonight, re-set the timing (thanks Crazyhorse!!) and ran it a few minutes on the hose at 1000 rpm. Small fuel leak that took a few minutes fix and I couldn't find one of the freeze plug petcocks that I took out Sunday (it was under the oil pan in the SAND!). Overall, I don't think I hurt anything in the short time I ran a little hot. Never saw over 200 on the oil temp and never got over 190 on the water before I shut her down. Never smelled anything hot (burned rubber or oil). So, tomorrow I'll run it on the lake and set the total advance.

Wish me luck!!!

Mike
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
Waterfoul is offline  
Old 09-03-2002, 10:23 PM
  #2  
Registered
 
Frequency's Avatar
 
Join Date: Aug 2001
Location: Peoria, IL & FMB, FL
Posts: 1,008
Likes: 0
Received 1 Like on 1 Post
Default

Good Luck Mike!!!!!
Frequency is offline  
Old 09-03-2002, 10:33 PM
  #3  
Registered
 
mika's Avatar
 
Join Date: Apr 2002
Posts: 255
Likes: 0
Received 0 Likes on 0 Posts
Default

Hey Mike, Here's a picture from the Big Dicks run. Good luck with the motor.
Attached Thumbnails Dug into my motor tonight.......good news!!!-foul.jpg  
mika is offline  
Old 09-03-2002, 10:46 PM
  #4  
Gone Fishin'
Charter Member
Thread Starter
 
Waterfoul's Avatar
 
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes on 0 Posts
Default

Sweet!! Thanks Shane.
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
Waterfoul is offline  
Old 09-03-2002, 10:47 PM
  #5  
Registered
 
Crazyhorse's Avatar
 
Join Date: Jan 2001
Location: Holland MI
Posts: 3,140
Likes: 0
Received 0 Likes on 0 Posts
Default

No problem Mike. Glad I could help, even if it was from 30 miles away.
Crazyhorse is offline  
Old 09-04-2002, 07:21 AM
  #6  
Charter Member #30
Charter Member
 
Scott's Avatar
 
Join Date: Oct 2000
Location: Bellville,Oh
Posts: 2,163
Likes: 0
Received 14 Likes on 5 Posts
Default

Hey Foul,
Long time no talk to I read the posts about the strainer or should I say the debate
If it was me I'd still install one it should act as a buffer between the drive and the motor you may still get sand in the motor but not as fast (diluted) hopefully it would just go through the engine without packing up the lines. Nice pictures!
I found two strainers for my boat on OSO from another member for 200.00 and they are Gills look and work great. Every time I go to PIB I need to clean them out (looks like a huge ceaser salad).
Scott
__________________
I have Steps & Bubbles!

Last edited by Scott; 09-04-2002 at 07:23 AM.
Scott is offline  
Old 09-04-2002, 07:52 AM
  #7  
Charter Member #232
Charter Member
 
Audiofn's Avatar
 
Join Date: Oct 2000
Location: Carlisle, MA USA
Posts: 18,422
Received 6 Likes on 4 Posts
Default

Good to hear foul and if your temps never got over that then I would think you are totally fine. Do not forget to retorque your intake after you heat it up and cool it down I did that once and it messed up my day.
__________________
Put your best foot forward!
Audiofn is offline  
Old 09-04-2002, 08:24 AM
  #8  
Official OSO boat whore
Charter Member
iTrader: (2)
 
Join Date: Oct 2000
Location: Mequon, WI
Posts: 6,157
Likes: 0
Received 0 Likes on 0 Posts
Default

So, was the gasket blown at the riser? Did it burn through the gasket or was there a metal block off plate? And yes, don't forget to retorque!
Cord is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Sick Stinger
Northeast US
0
07-08-2008 08:35 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



Quick Reply: Dug into my motor tonight.......good news!!!


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.