Go Back  Offshoreonly.com > General Discussion > General Boating Discussion
Horsepower VS Gear Ratio question >

Horsepower VS Gear Ratio question

Notices

Horsepower VS Gear Ratio question

Old 08-26-2015, 09:14 AM
  #1  
Registered
Thread Starter
 
Join Date: Jul 2012
Location: On the Saginaw River dodging logs
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Question Horsepower VS Gear Ratio question

Lets say a boat with a 1.5 geared bravo was switched to a 1.36 ratio AND the correct pitch prop to obtain the same output.

Will the engine have to work harder with a 1.36 ratio to achieve the same results as the 1.5 ratio?

Thanks
illMATTic is offline  
Old 08-26-2015, 09:18 AM
  #2  
Racer
Racer
 
Wahoo ATV's Avatar
 
Join Date: Jan 2006
Location: Columbus,MI
Posts: 2,574
Likes: 0
Received 1 Like on 1 Post
Default

not if the prop is changed to achieve the same speed at same rpm, which may not be possible

50mph at 4000 rpm is still 50mph at 4000rpm regardless of ratio to achieve that.

Last edited by Wahoo ATV; 08-26-2015 at 12:30 PM.
Wahoo ATV is offline  
Old 08-26-2015, 09:33 AM
  #3  
Registered
iTrader: (5)
 
Join Date: Jul 2009
Location: Taunton Ma
Posts: 8,527
Received 698 Likes on 341 Posts
Default

Unless prop slip changes.
Unlimited jd is offline  
Old 08-26-2015, 09:47 AM
  #4  
Registered
Thread Starter
 
Join Date: Jul 2012
Location: On the Saginaw River dodging logs
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Default

Would there be more resistance on the smaller prop having to turn more rpm to achieve the same output?

I am not saying you are wrong. I am just trying to get all sides. I have been hearing conflicting theories.
illMATTic is offline  
Old 08-26-2015, 10:10 AM
  #5  
Registered
 
44MTI's Avatar
 
Join Date: May 2003
Location: E-Dock
Posts: 3,133
Received 1 Like on 1 Post
Default

I understand what everyone is posting and that it should be the same.
However, most people I know would rather have the lower gear ratio which multiplies your torque.
Also there is some advantage to turning the props faster as far as lift goes.
44MTI is offline  
Old 08-26-2015, 10:39 AM
  #6  
Registered
 
Join Date: Dec 2013
Location: Minneapolis, Mn
Posts: 358
Likes: 0
Received 2 Likes on 2 Posts
Default

Also think of it lt like a screw with fine vs course pitch, a course pitch screw will take more HP to turn thru the water then a finer pitch spinning faster.

Atleast thats how I was told and makes sense in my head.
turbom700 is offline  
Old 08-26-2015, 11:52 AM
  #7  
Registered
iTrader: (1)
 
Join Date: Jul 2007
Location: MI
Posts: 2,639
Received 12 Likes on 6 Posts
Default

Originally Posted by 44MTI
I understand what everyone is posting and that it should be the same.
However, most people I know would rather have the lower gear ratio which multiplies your torque.
Also there is some advantage to turning the props faster as far as lift goes.
How does spinning the props faster affect lift? Would it increase stern lift?

I am asking because I am looking at a boat with 1.24 drives and it needs as much stern lift as possible.

BTW, Mercury only recommends gear changes when there are no available prop pitches left.

Last edited by JRider; 08-26-2015 at 11:55 AM.
JRider is offline  
Old 08-26-2015, 11:52 AM
  #8  
Registered
 
Join Date: Oct 2011
Location: Nevada, IA
Posts: 27
Likes: 0
Received 0 Likes on 0 Posts
Default

To me, it seems more efficient to turn a more aggressive pitch propeller slower to achieve the same speed.
Drivehard is offline  
Old 08-26-2015, 11:55 AM
  #9  
Registered
Thread Starter
 
Join Date: Jul 2012
Location: On the Saginaw River dodging logs
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by Drivehard
To me, it seems more efficient to turn a more aggressive pitch propeller slower to achieve the same speed.
This was my original understanding but it seems there are differing views. I have never tested it but will be shopping next season and I see there are many different power/drive combos out there.
illMATTic is offline  
Old 08-26-2015, 12:11 PM
  #10  
Registered
iTrader: (1)
 
onesickpantera's Avatar
 
Join Date: Feb 2005
Location: Michigan
Posts: 4,388
Received 21 Likes on 10 Posts
Default

Originally Posted by JRider
BTW, Mercury only recommends gear changes when there are no available prop pitches left.
This is what I have been told as well. However, I have heard that higher pitched props can be less efficient.

I bet if you asked 10 "prop experts", 5 would say one answer and 5 would say the other.
onesickpantera is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.