Start to Finish: Building Our 50' Skater
01-06-2018, 12:16 PM
#1541
Registered
Video: testing at Jordanelle reservoir.
check out the view/water at 2 min 15 sec
check out the view/water at 2 min 15 sec
Last edited by BigSilverCat; 01-06-2018 at 12:19 PM.
01-06-2018, 12:48 PM
#1542
Registered
Dead calm....deck camera from a 50' Skater on calm water is in keeping of the deck cam on a aircraft carrier.
Not many people can say they have ever gone to the lengths you have Tyson!
Not many people can say they have ever gone to the lengths you have Tyson!
01-06-2018, 02:43 PM
#1543
Registered
Join Date: Jan 2018
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for putting the time into sharing this thread it is the best. Great job you are doing on the boat . Wisseman were developing a 2 speed that was air operated and went onto an outboard trunk above the gearbox i saw it at SEMA back in 2010 or 2011, maybe they do one to go on an M8 .Good luck with this project it is absolutely the best thing I have ever seen online!
01-06-2018, 02:55 PM
#1544
Registered
iTrader: (1)
Crappy day there for sure. Mid to high 30's with a wintry mix coming down,
See a car at end of ramp so assuming they are still out there now?
https://stateparks.utah.gov/parks/jo...nt-conditions/
See a car at end of ramp so assuming they are still out there now?
https://stateparks.utah.gov/parks/jo...nt-conditions/
01-06-2018, 03:24 PM
#1545
Registered
Crappy day there for sure. Mid to high 30's with a wintry mix coming down,
See a car at end of ramp so assuming they are still out there now?
https://stateparks.utah.gov/parks/jo...nt-conditions/
See a car at end of ramp so assuming they are still out there now?
https://stateparks.utah.gov/parks/jo...nt-conditions/
Last edited by BigSilverCat; 01-06-2018 at 03:35 PM.
01-06-2018, 03:53 PM
#1547
Registered
if you notice the roost turns dark on the starboard side right at 9:40 that was when the turbo broke loose so the engine was not getting enough air to burn all the fuel and clean up the exhaust.
Last edited by BigSilverCat; 01-06-2018 at 03:57 PM.
01-06-2018, 04:11 PM
#1548
Registered
iTrader: (1)
we already left, here is the video of going back to industrial injections shop.
https://youtu.be/XPatqS4XFgo
https://youtu.be/XPatqS4XFgo
01-06-2018, 06:03 PM
#1549
Registered
Tyson - a bit of advice and maybe you are doing it already but you should monitor exhaust manifold pressure (not back pressure but between exhaust ports and turbo) and that should be right along side boost pressure, you know boost has to be higher than exhaust, when it is not the engine can't breath anymore and things melt - again not an expert just years of looking over damage.
01-06-2018, 06:33 PM
#1550
Registered
That starboard engine didn't look happy from the get go, it seemed to be steaming heavily at the start compared to the port.
Whats making to turbos let go? they should be the simplest part of the project if matched to the engine correctly and not over-speeding.
Here's one of my turbos off my motors what size inducer and exducer you running?
Whats making to turbos let go? they should be the simplest part of the project if matched to the engine correctly and not over-speeding.
Here's one of my turbos off my motors what size inducer and exducer you running?
Last edited by 999JAY; 01-06-2018 at 06:42 PM.
