Can you find these in white?
 

Can you find any of these gauges or just the bezels in white? Redoing all the gauges to Autometer white marine and want to match somewhat.

Does the bezel of the drive gauge pop off without taking it out? If so I will just paint to match cause that doesnt look fun to take out.

Thanks!

PS - Off subject but do any of you higher power stereo guys (5k watts+) run a lithium battery just for the subs amp? If so what brand? Looking at Glowe Voltage series 3.

https://cimg8.ibsrv.net/gimg/www.off...4c9ce530ab.jpg
https://cimg9.ibsrv.net/gimg/www.off...9456a8f5ba.jpg
https://cimg0.ibsrv.net/gimg/www.off...b78d0034cb.jpg
https://cimg1.ibsrv.net/gimg/www.off...9e0183a371.jpg

What's your thinking on incorporating a LiFeP04 battery? Adding as a standalone or replacing an existing flooded cell type battery? How are you planning on charging it if standalone? They have pretty rigid charging protocols necessary in order to get a full charge...just curious.

Their batteries work off stock alternators. All thats needed is the initial charge after shipping with the lithium charger. Reason why is I have 2 newer West Marine deep cycles and they cant power the subs with engine off. Dont know if they can with engine on or not since its out at the moment. I know those batteries do just fine with the (2) 1200.4 amps I have for mids and highs. Just dont do the subs. I even added another in series yesterday while out in the shop and it dont help. Sound decent at very low volumes but once turned up past 30% they dont have power needed. Subs are on a 2.5K amp.

You could just take them to a powder coater and have them done in white

The drive indicator is a complete assembly. The outer rim has studs that bolt it all together Marine Parts Plus Parts Search

I would loosen it enough to get tape behind it and paint it in place

When I did my dash and had panels made I had them make a new card for the trim gauges

https://cimg9.ibsrv.net/gimg/www.off...48fc966dd.jpeg
https://cimg3.ibsrv.net/gimg/www.off...51431ddb7.jpeg
https://cimg4.ibsrv.net/gimg/www.off...692fc57212.png

https://cimg5.ibsrv.net/gimg/www.off...4eff7b95c.jpeg
https://cimg6.ibsrv.net/gimg/www.off...e0727a9c3.jpeg

https://cimg9.ibsrv.net/gimg/www.off...b1858c071.jpeg
https://cimg9.ibsrv.net/gimg/www.off...bdc0bb644.jpeg

If you pull it apart you just have to be careful that you don’t lose the little springs on the indicators

Well hell...lol. Painting in place is just as big of a pain but less headache so thats that I guess. The others I should be able to 3d print or just paint. Thanks fellas!

[img alt="If you are going to paint in place don’t bother loosening the dash panel

This is the piece connected to the dash panel
The plate with the indicators bolts to the back of the bezel and springs hold the indicators in the guard

You can’t loosen the bezel up without taking this back piece off

Not sure if this makes sense but hope it helps"]https://cimg7.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/1206x1386/img_4790_f54adcd51d2444faeabc227d059849ac16579b69. jpeg[/img]
If you are going to paint in place don’t bother loosening the dash panel This is the piece connected to the dash panel The plate with the indicators bolts to the back of the bezel and springs hold the indicators in the card You can’t loosen the bezel up without taking this back piece off Not sure if this makes sense but hope it helps

https://cimg6.ibsrv.net/gimg/www.off...7a3b1cc1e.jpeg