Go Back  Offshoreonly.com > General Discussion > General Boating Discussion
Gelcoat restoring after removing graphics >

Gelcoat restoring after removing graphics

Notices

Gelcoat restoring after removing graphics

Old 03-26-2004, 01:56 PM
  #1  
Registered
Thread Starter
 
marinetrans's Avatar
 
Join Date: Nov 2003
Location: Fairhaven Ma
Posts: 833
Likes: 0
Received 0 Likes on 0 Posts
Default Gelcoat restoring after removing graphics

Anyone know how to get back gelcoat color after graphics are removed? Seems like the gelcoat under the graphics is "yellow" and the rest of the boat is white. What can I do?
marinetrans is offline  
Old 03-26-2004, 02:07 PM
  #2  
Registered
 
Join Date: Jul 2002
Location: Troy, Mich
Posts: 2,728
Likes: 0
Received 6 Likes on 5 Posts
Default Wow

I think the graphics were applied after the paint and between layers of Gelcoat. You may be screwed and have to reshoot the boat.

Wannbe
wannabe is offline  
Old 03-26-2004, 02:10 PM
  #3  
Registered
Thread Starter
 
marinetrans's Avatar
 
Join Date: Nov 2003
Location: Fairhaven Ma
Posts: 833
Likes: 0
Received 0 Likes on 0 Posts
Default

They were stick on vinyl graphics. I wonder if I have to wet sand the areas? They were black graphics. I peeled them off w/ heat gun.
marinetrans is offline  
Old 03-26-2004, 02:33 PM
  #4  
Registered
 
Join Date: Jul 2002
Location: Troy, Mich
Posts: 2,728
Likes: 0
Received 6 Likes on 5 Posts
Default Wet Sand

Yep start w/ 1200 to lightly polish the gel back

Sorry, I understood you had sanded them off
wannabe is offline  
Old 03-26-2004, 02:38 PM
  #5  
Registered
Thread Starter
 
marinetrans's Avatar
 
Join Date: Nov 2003
Location: Fairhaven Ma
Posts: 833
Likes: 0
Received 0 Likes on 0 Posts
Default

I tried Aqua-Buff but couldn't get the color back. But Aqua-Buff worked on the rest of the boat. So wet sand starting w/ 1200. I'll try that tommorow.
marinetrans is offline  
Old 03-26-2004, 03:15 PM
  #6  
Neno the mind boggler
VIP Member
iTrader: (1)
 
glassdave's Avatar
 
Join Date: Sep 2001
Location: toledo oh
Posts: 13,064
Received 259 Likes on 92 Posts
Default

i have run into this many many many times in my biz. hate to say it but once it is faded like that you may be screwed. you can try the sanding route but usually the fading runs very deep. i have tried several times (usually at customers request) but have never actually succeeded 100%. its worth a shot as apposed to painting though. be careful how far you sand though. i have had some that actually seemed to get worse or ended up with a larger even different color of gel. sorry if I'm the bringer of bad news. been there . . done that. best of luck
__________________
Throttles- Cleveland Construction 377 Talon
08 OPA Class 1 National Champion
08 Class 1 Geico Triple Crown Champion
08 OPA High Points Champion
10 OPA Class 1 National Champion ( happy now Ed! )
glassdave is offline  
Old 03-26-2004, 05:20 PM
  #7  
Registered
 
Join Date: Jan 2001
Location: Toms River NJ
Posts: 2,633
Received 13 Likes on 6 Posts
Default

I agree with Glassdave. I purchased a 24 Sunsation and after pulling off the old vinyl, it was apparent the rest of the hull had faded. Under the vinyl, the hull was very shinny. This was "protected" from the sun. No amount of wet sanding brought back the rest of the hull to match where the vinyl use to be.
Fast Shafts is offline  
Old 03-26-2004, 07:23 PM
  #8  
Registered
 
Join Date: Aug 2002
Location: Eastern Lake Ontario
Posts: 2,896
Likes: 0
Received 3 Likes on 3 Posts
Default

Hold on minute here Guys!!!! What marinetrans said was the hull was yellowed UNDER where the vinyl was, the surounding areas were bright and shiny.

I believe what has happened here is that the adhesive from the vinyl has leached into the gelcote.

First, I would try some bleaching agents such as "Slimy-Grimy" or other hull stain removal products. If that doesn't work,,,,,,, well,,,,,,, we have some problems.

If marinetrans has to sand the area under where the graphic was, he'll have to feather that sanding operation way out to make it look good. But, I don't think sanding is going to do the trick if in fact the adhesive has leached into the gelcoat. It's probably into the gel deeper than sanding can get to (without making a low spot).

I'm no expert, but leaching is my guess.
ThirdBird is offline  
Old 03-26-2004, 07:43 PM
  #9  
Registered
 
KNOT-RIGHT's Avatar
 
Join Date: Dec 2002
Location: Providence,RI
Posts: 3,359
Received 156 Likes on 84 Posts
Default

Pete,
If you decide to go with wet sand make sure you use a thin 1/8 rubber sanding block under the 1200.
I prefer 3M. Maybe you will get lucky and it has not
penetrated the gelcoat that deep.


Good Luck
Gerry
KNOT-RIGHT is offline  
Old 03-27-2004, 02:55 PM
  #10  
Registered
Thread Starter
 
marinetrans's Avatar
 
Join Date: Nov 2003
Location: Fairhaven Ma
Posts: 833
Likes: 0
Received 0 Likes on 0 Posts
Default

I might make it worse by trying to screw with it. I'd like to wet sand but the discoloration looks deep.Could be the glue that discolored it too. Its a perfect match to the graphics. Thinking about new graphics that will cover up most of it. Like the 3-D letters that said "BOXER" , I'll put "NOPPER" in 3-D. Might look better that way.
marinetrans is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
waterboy222
Fiberglass and Paint
21
03-11-2008 08:24 AM
fishead
General Boating Discussion
6
02-24-2005 03:02 PM
totalmp
General Boating Discussion
21
03-21-2004 07:49 PM
LPA2106
General Boating Discussion
7
02-19-2004 09:53 AM
Dave M
General Q & A
7
06-03-2003 10:16 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Quick Reply: Gelcoat restoring after removing graphics


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.