stellings
 

looking for a set of big tube stellings or cmi stainless headers . I have a set of greens but they come to far forward and will not allow my engine hatch to close

Re: stellings
 

Are They For A Bravo Set Up?

Re: stellings
 

my boat has bravo drive . my hatch comes down very close to the front of the engine and won't close with thease headers they come forward 9" past the valve covers

Re: stellings
 

I have a tripple set I will be putting for sale shortly.
Outer two are (Roid Yellow 15) big tubes & the center engine is (Roid Dk.Blue 12) Big tube. Blue is taller than yellow per Randy @ Stellings.

Sounds like mine may have a Hight issue also.

Roid Yellow is Shown below

Cougarman

Re: stellings
 

not so much a height issue as i am changeing where exhaust exits on transom but the greens sweep forward 9" in front of the valve covers

Re: stellings
 

How far in front of the valve cover can you go? I've got 4 sets for sale,all are different, none are big tube (roid) though.

Re: stellings
 

Posted a pic for ya, in my original post

Cougarman

Re: stellings
 

any chance of some pics with some dimensions of the ones you have ? you can send to [email protected] thanks I have only 3-4 inches in front of my valve covers where the hatch closes down

Re: stellings
 

how tall are thease from the flanges to the centerline of the collector?

Re: stellings
 

Not sure I can measure tonight


Cougarman

Re: stellings
 

I Have 1 Pair Of Cmi Sport Tube. For Bravo Set Up.

Re: stellings
 

Im lookin for a set for staggered motors. I believe they are black/yellows?

Re: stellings
 

what is primary tube id? can you send dimensions for thease also ? from flange to collector centerline

Re: stellings
 

I Have A Set Of Black LT Green Big Tube Mint Condition/// Cheap Any Offers

Re: stellings
 

Hope fully you can understand this, (ROID YELLOW 15)
from the center line of the lowest row of bolts on the
flange is 20 inches to the top of the header. Also
from the center of the very last bolt on the flange on the
collector end of the flange....to the end of the the 4"
collector is 14inches.

(ROID DK.BLUE 12) from the center line of the lowest row of bolts on the flange is 22 inches to the top of the header. Also
from the center of the very last bolt on the flange on the
collector end of the flange....to the end of the the 4"
collector is 14inches.

Short tail pipes, two are 24inch long two are 27inch long.
Long tails pipes, one is 71 1/2 inch long the other is 74 1/2inch long.

Hope this helps
Cougarman

Re: stellings
 

What kind of boat? 3 of the 4 sets I have are out of a quad engine 50 Nortech. I don't think I have 2 sets that would work but maybe one. The ones I have were built in 01 and refurbished by Stellings in 04. I ran one set on the dyno once since then. 2k a set with tails

Re: stellings
 

Its a 32 Velocity/Thoroughbred. actually need the set for the foward motor. they are the ones that wrap up around the valve cover on the right side of the motor. The motor is on the left side of the boat.

Re: stellings
 

I think I've got what you need. By left you mean port? I've got a set of Blk./Lt. Green that measure 20.5" from center of collector to center of collector on a tall deck (10.200") with Merlins. The end of the Stbd. collector is 10.75" past the rear surface of the block. The port is 8" past. I can send you pics if you give me an e-mail to send to.

Re: stellings
 

Ben, email is [email protected]

I'll check those measurements tonite.

Re: stellings
 

THE TUBE ID IS 2 INCH AND FROM FLANGE TO COLLECTOR
IS 7 3/4 FROM COLLECTOR TO BOLT HOLE. HOPE THIS HELPS .