AFR heads and matching roller for a 454 mark IV short deck 89-90
#1
Registered
Thread Starter
Join Date: Feb 2008
Location: Norway
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
AFR heads and matching roller for a 454 mark IV short deck 89-90
As the title say im looking for a top end kit for this engine and i have been searching the net alot to find parts to use on this settup, the engine is original a volvo 7,4 litres fresh water cooled marine engine Oval port ,casting number on the block is 10069286 and if im right its a mark IV-454-89/90 4 bolt short deck.
the engine block is borred 0,30, small dome forged piston. new Eagle forged cranck stock stroke, Hbeam Eagle forged rods arp 7/18 bolts, rotating parts is dynamicaly balanced.
Have Msd 6al marine ignition box coil and distributor.
Victor j singleplane intake manifold.
Gonna buy Keith Eickert Exhaust Thunder-N-Lightning Cast Aluminum Exhaust Headers #16660 .
http://www.diamondperformanceparts.c...cat=282&page=1
piston spec.
Sealed Power #844-L2399NF30
454ci Open Chamber Head Race Piston, .030'' Overbore
Piston Dia.: 4.280''
Piston Top: .095cc Dome
Pressed or Floating Pin
Comp Ratio: 10.23:1 w/100.9cc Heads,
Ring Grooves: 5/64'', 5/64'', 3/16'' .
read alot of the post in here and 1 name have been coming up alot , Bob Madara from Marine Kinetichs. already sendt a mail to him about this , but no answer. well after all the good things i read about him in here im guessing he has hell of alot to do,
no answer yet.
What im looking for is AFR heads complete with springs retainers ,seals and a matching roller cam that will get the most out of this settup. this engine is going into a revenger 27 feet san marino on a bravo xr 1.50 drive ratio.
Hopefully anyone out there with the expertise can help me with this i realy need to get this engine assembled and ready for the boat.
the engine block is borred 0,30, small dome forged piston. new Eagle forged cranck stock stroke, Hbeam Eagle forged rods arp 7/18 bolts, rotating parts is dynamicaly balanced.
Have Msd 6al marine ignition box coil and distributor.
Victor j singleplane intake manifold.
Gonna buy Keith Eickert Exhaust Thunder-N-Lightning Cast Aluminum Exhaust Headers #16660 .
http://www.diamondperformanceparts.c...cat=282&page=1
piston spec.
Sealed Power #844-L2399NF30
454ci Open Chamber Head Race Piston, .030'' Overbore
Piston Dia.: 4.280''
Piston Top: .095cc Dome
Pressed or Floating Pin
Comp Ratio: 10.23:1 w/100.9cc Heads,
Ring Grooves: 5/64'', 5/64'', 3/16'' .
read alot of the post in here and 1 name have been coming up alot , Bob Madara from Marine Kinetichs. already sendt a mail to him about this , but no answer. well after all the good things i read about him in here im guessing he has hell of alot to do,
no answer yet.
What im looking for is AFR heads complete with springs retainers ,seals and a matching roller cam that will get the most out of this settup. this engine is going into a revenger 27 feet san marino on a bravo xr 1.50 drive ratio.
Hopefully anyone out there with the expertise can help me with this i realy need to get this engine assembled and ready for the boat.
Last edited by GhosT; 07-26-2012 at 03:45 PM.
#2
Fast Singles Club
Gold Member
iTrader: (8)
Call Bob at 585-654-8583 or send an e-mail to [email protected]
Last edited by the deep; 07-26-2012 at 10:20 PM.
#3
Registered
Thread Starter
Join Date: Feb 2008
Location: Norway
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Call Bob at 585-654-8583 or send an e-mail to [email protected]
so emails is the way to go for me , but thx for that other email im gonna resend on that on to.
I think this are the heads im gonna need but i also need a roller to match it , would been nice to order all from the same place and know that you get quality parts, and what i read in here Bob seems to be the man.
In norway there isnt many with the expertise to setup this kind of parts, and if it was the prices here is 3 times what i pay to get parts directly from us with shipping
http://www.airflowresearch.com/index.php?cPath=68_121
Last edited by GhosT; 07-27-2012 at 03:12 AM.
#4
Registered
iTrader: (1)
Join Date: Jul 2009
Location: ct/fl
Posts: 1,659
Likes: 0
Received 0 Likes
on
0 Posts
Call Bob at 585-654-8583 or send an e-mail to [email protected]
#5
Registered
+2 you can't do any better.
#6
Registered
Thread Starter
Join Date: Feb 2008
Location: Norway
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Many thx to the deep, that email address you posted got me an answer just a few houers after i resendt from BOB M.
seems like the internal parts i have are spot on for the afr 290 cnc heads , just some small details to fill in and parts coming my way
many thx again ^^
seems like the internal parts i have are spot on for the afr 290 cnc heads , just some small details to fill in and parts coming my way
many thx again ^^
#8
Registered
Make sure you post your results, we're interested in what's going on across the pond.