|
this one was seriously on my list!!
keep us updated!!! |
There was a thread in the fountain section about someone doing a similar job. I think it was In a 42.
|
Originally Posted by chris_dobz
(Post 4099739)
I realize that I will have to make a substantial investment in tools which is yet another I'll need to know before I start but other than that I'm mentally prepared and looking forward to the challenge.
Cheers, Chris |
Will do! I'm in VA Beach this Friday for my final survey. It doesn't run so I'm also bringing my mechanic with me. I have a laundry list of concerns with this rig but hopefully things go better than expected.
Originally Posted by jeff32
(Post 4099747)
this one was seriously on my list!!
keep us updated!!! |
Do you have the link handy?
Originally Posted by 88bullet
(Post 4099748)
There was a thread in the fountain section about someone doing a similar job. I think it was In a 42.
|
why waste money on survey your going to do work anyway order your wood and buy sawzall angle grinder tyvec suit and resperator take lots of pic and the biggest thing in fiberglass work is be sure everything is ground clean and no sharp edges on anything new round all edges
|
That's a LOT of hard work. With all of the big triple engine boats for sale right now that no one seems to want, AND are difficult to insure (have you checked this?)...
...if it were MY money and time, I'd get into something that was ready for the water right now. Even if you have to finance; what is your time worth to you? You are never going to get the $$ investment back on the boat. If you could double down on the something else you do well & efficiently for $$ (side jobs, extra hours, other stuff); I'd look into financing or obtaining a boat that is ready to run. This is one instance where $$ can buy you time; and that's the 1 thing that hardest to come by. Time boating with family & friends, and enjoying life is much better than grinding, gluing, and wrenching for what, maybe a full season, or more? Just my $.02. Also, I would not use Seacast or any of the pourable systems in an offshore boat for anything structural. |
best way to find out what you really have going on in suspect area's is to drill down into them...see what wood looks like coming out...you will know quick how bad/deep etc....
|
Have to agree with Sydwayz here.. from the looks of that boat of what's posted on Boat Trader, you're going to be spending a LOT of time and money getting that boat ready for the water and in the end you will still have a hull that's 16+ years old.
These 47's need a lot of care and feeding; I just dropped close to $30K getting my 47 in shape and that's for a 2009 that was in GREAT condition. Granted, a lot of what I did was preventative but mainly because I don't want to miss a minute of the boating season if I can help it.. And in these boats, everything is times 3... Sydwayz also has a good point on the insurance... very few carriers will cover this boat... my insurance went from $840 / year on my 38 to $4,100 on the 47. If you're in this for the sport of the project, then I guess it makes sense for you, but there's definitely a bunch of 47's out there that you could probably get into faster and have better resale value in a market that's already softer than a baby's bottom. I've looked at almost every one of them, so if I can help, feel free to ask.. |
Originally Posted by chris_dobz
(Post 4099486)
I am looking to buy a bank owned 1998 47' Fountain Lightning but the marine survey mentioned that there are a few spots on the stringers that sound like there might be some rot. So I am having Jeff with Invasion Boat Works (www.invisionboatworks.com) put together a proposal and estimate on the total cost to rip out everything and replace all three stringers in an attempt to get the bank to significantly lower its asking price. Knowing that the surveyor found some questionable spots I am assuming that right off the bat that I would want to replace all three stringers. The ball park pricing I received from Invasion Boat Works using something called Seacast was about $20K out the door for them to do all the work including tearing out all the interior.
Has anyone on this forum owned a 90's 47' Fountain Lightning that needed new stringers and if so what was the process, who did you use and how much did it cost you in the end? Also, is there any real benefit to using Seacast over marine plywood? What is the cost difference between Seacast and Plywood and what would be my cheapest option to replace the stringers? Thanks for your help in advance! - Chris Is it a triple engine boat? If so and your considering this much work,.. then I would change it to a staggered and sell of your third set of hardware. You can always re-sell a staggered easier than a triple also. Jon |
| All times are GMT -5. The time now is 11:22 AM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.