Notices

Pre-oiler?

Old 09-14-2017, 07:18 AM
  #1  
Registered
Thread Starter
 
Join Date: Feb 2012
Location: westville, NJ
Posts: 4,031
Likes: 0
Received 10 Likes on 8 Posts
Default Pre-oiler?

I get these brilliant ideas. And it turns out that everybody either figured it out already or it is stupid after all. You get a 12v scavenge pump. Makes about 30 psi. Feed it off oil cooler line. Put a check ball in block on oil galley fitting. Turn on key. Fire up scavenge pump. Watch oil pressure gauge climb to 30 psi. Start engine. What is wrong with this brilliant idea? Cost about 60 to 100 bucks.
dereknkathy is offline  
Old 09-14-2017, 07:38 AM
  #2  
Registered
iTrader: (1)
 
Join Date: Jun 2011
Location: Henderson, KY
Posts: 2,167
Received 80 Likes on 56 Posts
Default

One for sale here....
http://www.offshoreonly.com/forums/s...pre-luber.html
ALL_IN! is offline  
Old 09-14-2017, 10:25 AM
  #3  
Registered
iTrader: (7)
 
Join Date: Feb 2009
Location: NW Michigan
Posts: 8,299
Received 1,481 Likes on 802 Posts
Default

I did the same basic thing when I set up my 496's. Many argue it's not necessary but I did it anyway. Our boating season is so short up here in the north I figured it certainly couldn't hurt anything and only help. I had switches for the dash to run pumps and then I never finished the project due to some other implications and started new project with new builds however plan to use same set up with the 548 SC's. Whether or it prolongs bearing life who knows but I personally like the idea of it. I always figured if an oil pump ever failed which is not likely you could always flip the electric pump on.
getrdunn is offline  
Old 09-14-2017, 10:47 AM
  #4  
Registered
 
Join Date: Oct 2005
Location: New Hartford CT
Posts: 756
Likes: 0
Received 1 Like on 1 Post
Default

Originally Posted by getrdunn
I did the same basic thing when I set up my 496's. Many argue it's not necessary but I did it anyway. Our boating season is so short up here in the north I figured it certainly couldn't hurt anything and only help. I had switches for the dash to run pumps and then I never finished the project due to some other implications and started new project with new builds however plan to use same set up with the 548 SC's. Whether or it prolongs bearing life who knows but I personally like the idea of it. I always figured if an oil pump ever failed which is not likely you could always flip the electric pump on.
IMO, if the oil pump ever failed, it would too late for the pre-lube pump.

Ken
minxguy is offline  
Old 09-14-2017, 10:51 AM
  #5  
Registered
Thread Starter
 
Join Date: Feb 2012
Location: westville, NJ
Posts: 4,031
Likes: 0
Received 10 Likes on 8 Posts
Default

Originally Posted by minxguy
IMO, if the oil pump ever failed, it would too late for the pre-lube pump.

Ken
more than likely. but it might get second engine 10 seconds of run time to hit the dock...
dereknkathy is offline  
Old 09-14-2017, 05:50 PM
  #6  
Registered
iTrader: (7)
 
Join Date: Feb 2009
Location: NW Michigan
Posts: 8,299
Received 1,481 Likes on 802 Posts
Default

Hah... I've never had an oil pump fail on any engine so I will just stick with the OT and personally support the installation of but it's just a matter of choice.
getrdunn is offline  
Old 09-17-2017, 12:50 AM
  #7  
Registered
 
Join Date: Mar 2014
Posts: 61
Received 1 Like on 1 Post
Default

What about a 3 qt Accusump ?
Never tried one on a marine engine though,
but worked great on our race car engines...
chancer540 is offline  
Old 09-17-2017, 01:51 PM
  #8  
Charter Member #394
Charter Member
iTrader: (1)
 
SFOcean's Avatar
 
Join Date: Nov 2000
Location: CA
Posts: 533
Received 35 Likes on 17 Posts
Default

Canton has a two quart marine version (in blue) with the electric control valve.
Accusump by Canton Racing Products
SFOcean is offline  
Old 09-17-2017, 02:05 PM
  #9  
BUP
Banned
iTrader: (9)
 
Join Date: Jul 2011
Location: Ft. Worth TX
Posts: 9,594
Likes: 0
Received 41 Likes on 35 Posts
Default

We use this and I am very happy with it. Simple system and less leak points with no added weight in the engine compartment.

Filter - Large Remote Primer Filter Mount - Peterson Fluid Systems
BUP is offline  
Old 09-18-2017, 07:50 AM
  #10  
Registered
iTrader: (1)
 
Join Date: Jun 2011
Location: Henderson, KY
Posts: 2,167
Received 80 Likes on 56 Posts
Default

That looks like a nice unit - don't think I've seen one before.
Originally Posted by BUP
We use this and I am very happy with it. Simple system and less leak points with no added weight in the engine compartment.

Filter - Large Remote Primer Filter Mount - Peterson Fluid Systems
ALL_IN! is offline  

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.