Offshoreonly.com
Page 13 of 31
« First
3
11
12
13
14
15
23
Last »
Show 40 post(s) from this thread on one page

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   Pantera (https://www.offshoreonly.com/forums/pantera-39/)
-   -   The rebuild of the Pantera coloured 509 (https://www.offshoreonly.com/forums/pantera/148810-rebuild-pantera-coloured-509-a.html)

tomas_wallin 05-25-2007 08:48 AM
Originally Posted by MIAMIBOYS (Post 2140144)
Can`t wait to see the Gen 3` on there. Tomas you will see a big gain in power.
Yeah, me too! :D It will be really interesting dynoing it. I will do my best to get a pull on the dyno with the Gen III's when everything is set and tuned.

tomas_wallin 05-30-2007 03:12 AM
Test mounted a piston to check the clearance of the rod bearings and now I have to get new bearings... Only ~.002 clearance and am looking for ~.003. Got the last set from a engine builder and will mount the pistons tomorrow. Finally...

tomas_wallin 05-30-2007 09:48 AM
Wanted!!!
 
Does anyone have a 8mm pulley for a 8-71 blower laying around?!

Looking for 50, 51 or 52 tooth pulleys.

Mange 05-30-2007 09:53 AM
Originally Posted by tomas_wallin (Post 2144889)
Does anyone have a 8mm .

8mm pulley??? Good luck with more HP HAHAHAHAHA

tomas_wallin 05-30-2007 10:03 AM
Originally Posted by Mange (Post 2144897)
8mm pulley??? Good luck with more HP HAHAHAHAHA
Sucker! :evilb:

Like one of these! :p

MIAMIBOYZ 05-30-2007 01:38 PM
Tomas you want to be at around 2.5 to 2.8 clearance all the way around. 2 is a bit tight unless you run real thin oil which is not good for a blower motor.

tomas_wallin 05-31-2007 04:04 AM
Originally Posted by MIAMIBOYS (Post 2145230)
Tomas you want to be at around 2.5 to 2.8 clearance all the way around. 2 is a bit tight unless you run real thin oil which is not good for a blower motor.
Yep, I got the .001 eXtra clearance bearings yesterday. That will get me to around .003 clearance with the rod bearings, same as the mains.

The Pantera should be repaired and ready to mount the fueltank and floor this weekend. :D

Mange 05-31-2007 04:58 AM
Hey Tomas,

Do you join us later today helping splash some boats?
Bring some beers....HA HA HA HA

tomas_wallin 05-31-2007 05:31 AM
Originally Posted by Mange (Post 2145989)
Hey Tomas,

Do you join us later today helping splash some boats?
Bring some beers....HA HA HA HA
Hahahaha, yeah right... :D It would be great though but i HAVE to get this engine together! :rolleyes: I have already lost two days in the schedule this week.

MikeyFIN 05-31-2007 07:33 AM
Originally Posted by tomas_wallin (Post 2144889)
Does anyone have a 8mm pulley for a 8-71 blower laying around?!

Looking for 50, 51 or 52 tooth pulleys.
Are they same as on a 14-71 ;-)?
If yes I might know a few...but they are accustomed to Top Fuel.

Glad to see your Project.


All times are GMT -5. The time now is 11:42 AM.
Page 13 of 31
« First
3
11
12
13
14
15
23
Last »
Show 40 post(s) from this thread on one page


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.