Offshoreonly.com - Search Results

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: bob
Showing results 1 to 25 of 45
Search took 0.02 seconds.
Forum: Swap Shop
06-14-2023, 06:38 PM
Replies: 0
Views: 743
Posted By bob

454 Mag Motor Complete

Purchased a 1995 Boat with a 454 Mag engine that had a block crack over the winter and owner started and tried to run motor until it filled with water , and oil. Luckily it was in a fresh water...
05-25-2023, 02:32 PM
Replies: 4
Views: 958
Posted By bob

New Boat in Fort Myers

Saw what looked to be a new boat to SWFL on the water today. And it looks like a dandy!...
Forum: Swap Shop
02-17-2023, 04:25 PM
Replies: 9
Views: 778
Posted By bob

Dan sorry I wasn't clear. The props I have are 5...

Dan sorry I wasn't clear. The props I have are 5 blades. The props I am selling are 4 blades. I have a pair of 5 blades up with Scott Baker. Probably going to clean them up add some cup. What...
Forum: Swap Shop
02-15-2023, 07:11 PM
Replies: 9
Views: 778
Posted By bob

Dan I am thinking you already have a pair or two...

Dan I am thinking you already have a pair or two of 29 or 30 pitch wheels. It is interesting to compare these to 17.75 or 18 " five blades. From a cruising standpoint their slip does very well...
02-04-2023, 07:06 PM
Replies: 21
Views: 5,536
Posted By bob

Give Keith a call or text at 386-503-7585.

Give Keith a call or text at 386-503-7585.
Forum: Southeast US
12-04-2022, 06:35 PM
Replies: 23
Views: 4,590
Posted By bob

Fort Myers Beach, Sanibel, Captiva and Pine...

Fort Myers Beach, Sanibel, Captiva and Pine Island still in pretty rough shape. Cape has most of their boat ramps open. Most marinas are still messed up. A few on the water restraunts open. ...
11-07-2022, 06:19 PM
Replies: 10
Views: 1,419
Posted By bob

Amsoil it is in the 6. Thank you for the feed...

Amsoil it is in the 6. Thank you for the feed back! Nice to know I will not be the first on the block to run it! Dan I too have been running F Type trans fluid in the trannies for many years with...
10-28-2022, 08:38 PM
Replies: 6
Views: 940
Posted By bob

Well my "co-pilot" has spoken and is not real...

Well my "co-pilot" has spoken and is not real interested in waking up the hood. So I believe I am going to leave things alone. Thanks much for the help!
Forum: General Q & A
08-16-2022, 04:54 PM
Replies: 19
Views: 1,632
Posted By bob

Can't just put 11Qts of oil in, fire motor and...

Can't just put 11Qts of oil in, fire motor and mark the sticks?
04-14-2022, 12:09 PM
Replies: 7
Views: 4,743
Posted By bob

And I need to give credit to Markel for being the...

And I need to give credit to Markel for being the least interested and price competitive. They are actually proud of it to boot!
Forum: General Q & A
03-12-2022, 06:06 PM
Replies: 34
Views: 5,110
Posted By bob

Ran those for years. KE used them allot. I am...

Ran those for years. KE used them allot. I am currently running some thermos from Improved Racing that seem to do well.
Forum: Outerlimits
02-11-2022, 12:43 PM
Replies: 33
Views: 13,779
Posted By bob

Awesome Bob! Gonna leave it FL for a bit? I...

Awesome Bob! Gonna leave it FL for a bit? I think we are needing some I/O exposure! LOL Looks great!
01-31-2022, 03:36 PM
Replies: 25
Views: 3,466
Posted By bob

Looking at an old KE dyno run. 750 hp at 6700. ...

Looking at an old KE dyno run. 750 hp at 6700. BSFC of .55. .55 x 750 = 412# / hr. 412 / 6.3 (weight of gas) = 66.7 GPH. At least on these motors.
Forum: General Q & A
12-27-2021, 01:22 PM
Replies: 254
Views: 45,672
Posted By bob

I used to have a guy put my heads on a flow bench...

I used to have a guy put my heads on a flow bench and put a piece of yarn in the air path and watch to see where the circular pattern was in the chamber and then re-configure squish area to get...
Forum: General Q & A
12-25-2021, 01:30 PM
Replies: 254
Views: 45,672
Posted By bob

Race boat app?

Race boat app?
Forum: General Q & A
12-23-2021, 09:00 AM
Replies: 254
Views: 45,672
Posted By bob

Looks like a nice piece except I don't believe it...

Looks like a nice piece except I don't believe it is available for tall deck though.
Forum: General Q & A
12-12-2021, 10:30 AM
Replies: 212
Views: 31,155
Posted By bob

Amen! Back in late 90"s cut my teeth on Merc...

Amen! Back in late 90"s cut my teeth on Merc Class 1's with KInsler EFI, Big Chiefs, .720" lift sticks etc. Dyno at 7200. Cool! Lap top was out once a month, EFI worked very well, kinda. ...
Forum: General Q & A
12-12-2021, 09:01 AM
Replies: 212
Views: 31,155
Posted By bob

Surprised no one has mentioned the...

Surprised no one has mentioned the quality/accuracy level of dash 2" boost guages. A few years ago , I noticed some differences in boost readings, on fresh blowers, I naturally ordered some new...
11-30-2021, 07:43 PM
Replies: 22
Views: 2,569
Posted By bob

Dan just ordered two 5 gallon buckets Boostane...

Dan just ordered two 5 gallon buckets Boostane Prof. thru Boostane. Delivered $599.99. Bought 5 gallons through Amazon a few weeks ago and it was $425.99 delivered. So for $175 I got an additional...
Forum: General Q & A
11-27-2021, 10:20 AM
Replies: 254
Views: 45,672
Posted By bob

He never manufactured them for Big Chief heads.

He never manufactured them for Big Chief heads.
Forum: General Q & A
11-26-2021, 07:48 AM
Replies: 254
Views: 45,672
Posted By bob

Darts have the pad to mount the injectors at the...

Darts have the pad to mount the injectors at the port. One of KE's main reason for staying with the Dart historically. I think probably the Profiller flows a little more. With either intake, port...
Forum: General Q & A
11-12-2021, 08:45 AM
Replies: 212
Views: 31,155
Posted By bob

KE spec'd cams from GS Products (RIP Glen). Lift...

KE spec'd cams from GS Products (RIP Glen). Lift is like .638". Not sure on duration. Lash is .009" and .011". Try to check lash every 20 or so hours. T&D rockers. Very little change after...
Forum: General Q & A
11-12-2021, 07:49 AM
Replies: 212
Views: 31,155
Posted By bob

Dan I run Crower 66291X903H-16 lifters with 9385+...

Dan I run Crower 66291X903H-16 lifters with 9385+ springs in at 2.080" right around 236# and 570# open. Change lifters out at 125 hours and springs at 250 and rockers rebuild at 250. Spray springs...
Forum: General Q & A
11-11-2021, 07:27 PM
Replies: 212
Views: 31,155
Posted By bob

You will probably end up with some extra height...

You will probably end up with some extra height on the bush for a little more stability. You also get the bigger axle bearing with the .904. I have been using Crowers with the pin oiling. KE's...
11-09-2021, 11:35 AM
Replies: 46
Views: 6,234
Posted By bob

I have also replaced them on the boat. PIA but...

I have also replaced them on the boat. PIA but it can be done.
Showing results 1 to 25 of 45
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.