Offshoreonly.com

Offshoreonly.com (https://www.offshoreonly.com/forums/)
-   Prop Talk (https://www.offshoreonly.com/forums/prop-talk-165/)
-   -   supercharged 25 outlaw prop size ? (https://www.offshoreonly.com/forums/prop-talk/182991-supercharged-25-outlaw-prop-size.html)

rod 03-25-2008 09:58 PM

supercharged 25 outlaw prop size ?
 
I am trying to get between 5400-5600 rpm any sugestions would be great her is my total package.

Boat: 1998 25-0' Outlaw.
Engine: 540 BBC,B&M 250 supercharger dynoed @ 727 hp & 686 ft lbs torque @ 5400rpm smallpulley
& 4 lbs of boost.
Cooling system:Teague sea strainer thru super chiller
dumped thru transom,Large Imco oil cooler.
Fuel system: Areomotive pump & reg. single 1060
dominator nickerson blower carb,remove stock
one way stock ball valve @ fuel tank steady 7
lbs @ W.O.T. Note: Blew my 1st engine up
with only a couple hrs on it because of the one
way ball valve fitting at the tank baja puts in at
factory restricted the amount of fuel to the
engine leaned it out and that was it,won't do
that again.
Drive: XR sportmaster 2"shortie with shower no
extension box.
Steering: Imco dual ram not hyd.to the helm.
Top speed: 86-88 mph 4lbs 1000 ft above se level fresh
water 2-0' chop, bravo 4 blade 28 pitch non
labbed 220 degrees oil temp @ 5100 rpm.

Sent supercharger to teague they rebuilt it 100% they had mentioned it was very loose and i should see between 6-8lbs of boost.

Bawana 03-25-2008 10:53 PM

What is your drive ratio? With the speed you are getting @ 5100 you can't be running a 1.5, with a 28 pitch prop. If your drive is a 1.36, and you can spin that 28 up to 5600, you should hit 92 with a 12% slip. With the added boost from having your SC rebuilt, you might be able to pull the extra rpm. How much $$ did Bob charge you for the rebuilt on the 250? Good luck, and hang on.
Bawana

Bawana 03-25-2008 10:59 PM

P.S. I don't know what heads or cam your running, but, you would have to spin that 250 very hard to get 8psi. with 540 ci.
Keep that water flowing to that innercooler.
Bawana

rod 03-25-2008 11:21 PM

its supposed to be a 1:50 when i purchased it,bob charged me 800.00 & they polished it

Perlmudder 03-25-2008 11:21 PM

that sounds like its a wild ride! lets see some pics!

socalstone 03-25-2008 11:48 PM

30 pitch B1 would be a good start. See my reply in the baja forum.
hope it helps. post pics and vid on that bad boy!

tony stamis 03-26-2008 03:24 PM

i had a 25 outlaw 1999 with 509 merlin heads and a 420 mega blower dyno was 765hp i ran an xr with 2 inch shortie no box ran 92-95 with a bravo 28 out of the box 1.50 bravo rpm was i believe 5800-5900

tony stamis 03-26-2008 03:28 PM

baja
 
3 Attachment(s)
pic of baja

rod 03-27-2008 01:01 AM

That is one sweet 25 i can't seem to get that kind of rpm out of mine on the dyno hit 6100 before running out of hp.Did you ever try any other props,how many pounds boost,where is the boat now does it still have this same set up.

tony stamis 03-27-2008 07:12 AM

sold the boat and put the original motor back in it i also ran a hydro for a while boat needed alot of set up after motor came of the dyno 7psi on dyno in boat only 3/4 psi so i changed the pulley to get about 6/7 psi and then i had to re adjust the carb jets a little to get it just right. i still have some of the props.


All times are GMT -5. The time now is 11:36 AM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.