|
Beautiful boat, can't wait to see what you end up with. Sorry if I missed it but what is your expected timeline for completion?
|
Originally Posted by Stclair26
(Post 4675795)
Beautiful boat, can't wait to see what you end up with. Sorry if I missed it but what is your expected timeline for completion?
Who knows... September 25....... of twenty twenty something.. 202__? Thanks for the kind words. Have you ever seen the boat when it was on st Clair? |
https://cimg9.ibsrv.net/gimg/www.off...021ee41c4.jpeg https://cimg0.ibsrv.net/gimg/www.off...83dc77cd8.jpeg https://cimg1.ibsrv.net/gimg/www.off...d61d92fb2.jpeg Ken sent some more pics that really got my excited today! hopwfully be done with this Florida Job soon and work work work on the boat! NJ —> MI 😁 |
We must keep FedEx and UPS in business. LOL.
|
Originally Posted by ren3
(Post 4675914)
We must keep FedEx and UPS in business. LOL.
its a 800 mile trip so I figured by the time I were to drive out there and back (1600 miles) and a day and a half’s worth of time that was pretty cheap. $240 in fuel and time or $325 to click a button. Easy choice |
Originally Posted by Rossman
(Post 4675866)
HAHAHAHAHAHA GOOD ONE! Who knows... September 25....... of twenty twenty something.. 202__? Thanks for the kind words. Have you ever seen the boat when it was on st Clair? |
https://cimg7.ibsrv.net/gimg/www.off...df984dae4.jpeg https://cimg9.ibsrv.net/gimg/www.off...8e43068ff.jpeg Resting on the stringer https://cimg6.ibsrv.net/gimg/www.off...d537c368f.jpeg https://cimg8.ibsrv.net/gimg/www.off...401fd0958.jpeg Thinking I need to go up a touch yet https://cimg0.ibsrv.net/gimg/www.off...dae112f00.jpeg Finally home! For a minute... Drives showed up and started playing around with the inner transom assembly plate to see what would need cut / moved / added to get the Arnesons on the hull. Will have to call Rik again now that I’ve got them in my hands to see about mounting height for the drives. Ken was nice enough to sand blast the boxes for me and put some new bearings in before sending them my way. Need to do some glass work on the transom and fill in all of the holes.... can’t wait! LOL |
Looks like a nice set-up I would be curious to know what Rik tells you for the installed height for the boxes mine are on a V hull and are mounted 1/2 in above the running surface directly in front of the boxes .
|
Got a hold of Rik again yesterday and assembled both drives. 5/8” - 3/4” above the bottom of the running surface to the rear most center of the box. I will not be able to achieve this as the outside would be dragging in the water. I am limited to 1/2” clearances on the bottom corners of the boxes. I will try and take some pics when it’s not just me around. Holding a straight edge, tape measure, and trying to take a pic is impossible! https://cimg0.ibsrv.net/gimg/www.off...79c75ad10.jpeg Dry fit together ( No silicon or thread lock etc). They went together very simply when I hung the box from the Hilo then lowered it onto the thrust tube to keep all of the u-joints and cardigan joint straight. Lower it down and spun the prop shaft and wahla. https://cimg9.ibsrv.net/gimg/www.off...778711a57.jpeg In much need of a spring cleaning soon https://cimg7.ibsrv.net/gimg/www.off...21446f441.jpeg Close to where she will land https://cimg8.ibsrv.net/gimg/www.off...39087105d.jpeg Going to start filling holes hopefully today. Need to get a scale for mixing resin / Hardner and I would like to get some thinner glass as well. Stay tuned |
What I ended up doing was make a jig using the motor center line , pin it to the bottom of the boat with some jacks put a peace of 1/2 wood for a spacer upward and it also doubled as a work bench and just set the boxes on top of that made real easy to draw around the boxes to set it up for the drill jig
|
| All times are GMT -5. The time now is 02:51 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.