Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: 2216terry
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Forum: Chris Craft
09-23-2011, 06:04 AM
Replies: 2
Views: 2,650
Posted By 2216terry

Thanks I will show this to my glass shop and see...

Thanks I will show this to my glass shop and see what he thinks. I am not going to do the job my self , I would break the glass for sure. that alone has me worried about even trying to mess with trim...
Forum: Chris Craft
08-22-2011, 07:12 PM
Replies: 2
Views: 2,650
Posted By 2216terry

Chris Craft 260 windshield rubber insert

I would like to replace the rubber insert around my windshield. But need to find a source. the boat is a 1986 260 scorpion, I bet most Chris Craft of this vintage have the same moulding if any one ...
Forum: Chris Craft
04-22-2011, 06:39 AM
Replies: 12
Views: 2,188
Posted By 2216terry

The mud and grit you plan to run in will eat the...

The mud and grit you plan to run in will eat the water pump impeller in the lower unit of the alpha one drive before the T stat gets pluged. Best to run the stock setup and stay out of mud. Mercury...
Forum: Chris Craft
04-18-2011, 06:29 AM
Replies: 12
Views: 2,188
Posted By 2216terry

Yes the engines do need a T stat. they need to...

Yes the engines do need a T stat. they need to run a minimum temp to operate properly. If the engine is too cold and you beat on it you could do a lot of damage.
Forum: Chris Craft
02-22-2011, 05:51 AM
Replies: 5
Views: 1,926
Posted By 2216terry

Did you know that Grew boats also made Wellcraft...

Did you know that Grew boats also made Wellcraft boats before the Chris Craft deal. All the Canadian built Chris Craft boats before 1988 that I have seen have been of great quality.
Forum: Chris Craft
10-26-2010, 06:10 AM
Replies: 5
Views: 1,926
Posted By 2216terry

Canadian Chris Craft

How did Grew of Canada fit into the Chris Craft family. Grew had all or most of the Chris Craft models made in Canada. They look and run just like Chris Craft made in any of the U.S. plants. Are they...
Forum: Chris Craft
02-25-2010, 06:11 AM
Replies: 6
Views: 1,755
Posted By 2216terry

You can not trim up high enough to not drag one...

You can not trim up high enough to not drag one gear case. with only one eng. running. P.S. you do not want to run differant gear ratios in only one drive you will not be able to
even out r.p.m....
Forum: Chris Craft
02-23-2010, 06:02 AM
Replies: 6
Views: 1,755
Posted By 2216terry

You are draging one gear case like an anchor with...

You are draging one gear case like an anchor with only one motor running. the v6 gear ratio will stand up just fine, but you will need to prop up to not over rev the v8 . your speed will not change....
Forum: Chris Craft
02-18-2010, 06:28 AM
Replies: 6
Views: 2,448
Posted By 2216terry

I have a 1986 260 stinger, also have stock 350,s...

I have a 1986 260 stinger, also have stock 350,s . I am running 21 p merc Qss props . they seem to work great for me.
Forum: Chris Craft
02-04-2010, 05:35 AM
Replies: 4
Views: 4,093
Posted By 2216terry

My manual for my 86, 260 scorpion stinger said...

My manual for my 86, 260 scorpion stinger said dry weight is 5500 lb. Now I have been told that is with out engiens, fuel or gear. If you are looking to buy a trailer best go at least 8000 lb. just...
Forum: Chris Craft
02-03-2010, 06:03 AM
Replies: 4
Views: 4,093
Posted By 2216terry

Try looking at weight of 260 scorpion in this...

Try looking at weight of 260 scorpion in this forum just below this one . I did not know they also made a 25 scorpion.
Forum: Chris Craft
12-15-2009, 05:02 PM
Replies: 2
Views: 4,011
Posted By 2216terry

Thumbs up weight of a stinger 260

I have a 260 stinger 1986[stock 260 hp mercs]. the book said dry weight is 5500 lb . I think not, loaded with fuel/water/gear it is on a 8000 lb trailer and the fit is very nice. not to much trailer...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.