Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: RigMaster
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Forum: General Boating Discussion
03-08-2011, 09:32 PM
Replies: 42
Views: 3,624
Posted By RigMaster

Krakatoa ...

Krakatoa

http://en.wikipedia.org/wiki/Krakatoa
Forum: Do It Yourself, Boating on a Budget
03-08-2011, 07:39 PM
Replies: 35
Views: 4,441
Posted By RigMaster

Bottom line is you need to take the drive/drives...

Bottom line is you need to take the drive/drives off when you are going to remove the motor/motors. I've seen guys do it without removing the drive,actually one guy and he had to remove the drive...
Forum: Do It Yourself, Boating on a Budget
03-08-2011, 12:17 AM
Replies: 35
Views: 4,441
Posted By RigMaster

Cool. For that price buy one. He has some cool...

Cool. For that price buy one. He has some cool stuff c_deezy.
I hope this helps him and Haley'sComet. Thanks for the link.
Forum: Do It Yourself, Boating on a Budget
03-08-2011, 12:08 AM
Replies: 35
Views: 4,441
Posted By RigMaster

Haley'sComet I just went over your reply again....

Haley'sComet I just went over your reply again. If you remove the transom assembly. you definitely need to use the alignment bar. sorry for the confusion.
Forum: Do It Yourself, Boating on a Budget
03-08-2011, 12:03 AM
Replies: 35
Views: 4,441
Posted By RigMaster

I would use the alignment tool in that situation...

I would use the alignment tool in that situation also. The engine sits on rubber mounts. sometimes they may be worn and when you remove them may go back down different. I've seen a few people do it....
Forum: Do It Yourself, Boating on a Budget
03-07-2011, 10:41 PM
Replies: 35
Views: 4,441
Posted By RigMaster

The Alignment bar allows you to adjust the engine...

The Alignment bar allows you to adjust the engine up or down,so that the outdrive shaft goes in straight.
I've seen people put them in without but they were kicking them till they could start the...
Forum: Do It Yourself, Boating on a Budget
03-07-2011, 08:09 PM
Replies: 35
Views: 4,441
Posted By RigMaster

Yeah U-joints and a new coupler gonna be in the...

Yeah U-joints and a new coupler gonna be in the future without it. And when you replace them and don't use the alignment tool. You'll be wondering why your replacing them again:lolhit:
Forum: Do It Yourself, Boating on a Budget
03-07-2011, 07:03 PM
Replies: 35
Views: 4,441
Posted By RigMaster

Another item you will need is an alignment bar....

Another item you will need is an alignment bar. With out that your gonna go through gimbal bearings. Real quick like.
Forum: American Offshore
03-07-2011, 07:00 PM
Replies: 103
Views: 20,761
Posted By RigMaster

Is Ed ferro/Red Still around?

Is Ed ferro/Red Still around?
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.