Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Lighting Bolt
Showing results 1 to 14 of 14
Search took 0.00 seconds.
Forum: General Q & A
06-04-2014, 10:09 PM
Replies: 10
Views: 4,267
Posted By Lighting Bolt

I have one id let go for $300 and you pay...

I have one id let go for $300 and you pay shipping. I know it ran when taken off but she has been sitting for a few years in a box. Don't rem what it was running other than a BBC and over 500ci.
Forum: General Q & A
02-04-2014, 07:17 PM
Replies: 275
Views: 229,348
Posted By Lighting Bolt

That one will work on a 6.0? Reason I ask is it...

That one will work on a 6.0? Reason I ask is it came up with 3 different ones and the only one that had a description of what it went on said 98-02 Camaro. Plus I dont know what the 6.0 falls under...
Forum: General Q & A
02-03-2014, 08:50 PM
Replies: 275
Views: 229,348
Posted By Lighting Bolt

You remember the part # on this flywheel? just...

You remember the part # on this flywheel? just wanna make sure I order the right parts for my 6.0 the 1st time and don't have any do overs.
Forum: General Q & A
01-03-2014, 12:00 PM
Replies: 275
Views: 229,348
Posted By Lighting Bolt

Well i finally got to go pick up my 6.0 out of a...

Well i finally got to go pick up my 6.0 out of a 07 2500. It has around 87,000miles on it and i picked it up for $1150. So since it was an automatic i need to get a flywheel for it, fab som brackets...
Forum: General Q & A
12-20-2013, 12:46 PM
Replies: 275
Views: 229,348
Posted By Lighting Bolt

Never said that 7000 was the moon on these but I...

Never said that 7000 was the moon on these but I still don't care to be twisting those rpms on my boat engine constantly when its factory gm parts. Plus on top of that I don't know how many rpms you...
Forum: General Q & A
12-20-2013, 09:16 AM
Replies: 275
Views: 229,348
Posted By Lighting Bolt

After some reading and research, your right they...

After some reading and research, your right they did make big power with the 4.8 on a dyno. But if you read into things more and think about it, a dyno isn't putting anywhere near the load on a motor...
Forum: General Q & A
12-19-2013, 07:57 AM
Replies: 275
Views: 229,348
Posted By Lighting Bolt

So a cam swap and turbo are they way to go on...

So a cam swap and turbo are they way to go on these motors? I am the same way on i don't don't want to be turning 7000rpms.
Id like to be making good power and never go over 5500rpm. Plus im still...
Forum: General Q & A
12-18-2013, 08:23 AM
Replies: 275
Views: 229,348
Posted By Lighting Bolt

But what all would it take to get one of the...

But what all would it take to get one of the lq4's to make 500hp? I know you said 450 with just a cam swap, headers and tune.
Forum: General Q & A
09-22-2012, 09:33 AM
Replies: 10
Views: 2,012
Posted By Lighting Bolt

I ran a scat 9000 crank in a budget built turbo...

I ran a scat 9000 crank in a budget built turbo motor for 3yrs. It was making around a 1000hp and It held up fine. As a matter of a fact the block ended up cracking before before I hurt anything...
Forum: Do It Yourself, Boating on a Budget
09-04-2012, 07:19 PM
Replies: 10
Views: 1,713
Posted By Lighting Bolt

Plus I'm figuring it's been altered a good bit by...

Plus I'm figuring it's been altered a good bit by Nickerson performance since it was built for a blower and isn't boost referenced.
Forum: Do It Yourself, Boating on a Budget
09-04-2012, 07:17 PM
Replies: 10
Views: 1,713
Posted By Lighting Bolt

I've tried settin them with up to .020 of the...

I've tried settin them with up to .020 of the slot showing past the blade to the blades being fully shut. I can even back the idle screws all the way off. I'm thinking the idle circuit is just way...
Forum: Do It Yourself, Boating on a Budget
09-02-2012, 09:20 PM
Replies: 10
Views: 1,713
Posted By Lighting Bolt

Dist is locked out at 30deg. I've worked on the...

Dist is locked out at 30deg. I've worked on the idle screws every way possible with no luck on the idle surge. If you set the idle at a 1000rpm or higher it's smooth but going below 1000rpm it's...
Forum: Do It Yourself, Boating on a Budget
09-02-2012, 07:43 PM
Replies: 10
Views: 1,713
Posted By Lighting Bolt

Also this is a 1050 dominator carb.

Also this is a 1050 dominator carb.
Forum: Do It Yourself, Boating on a Budget
09-02-2012, 01:59 PM
Replies: 10
Views: 1,713
Posted By Lighting Bolt

Carb tuning

Ok boys I have a 477 BBC with cast iron rectangle port hi-performance gm heads. Pretty mild motor 4" stroke, 6.135 rods with flat top forged pistons. The compression ratio comes up to about 8.25:1 on...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.