Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Scottski
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Forum: General Q & A
11-14-2022, 07:31 PM
Replies: 27
Views: 11,238
Posted By Scottski

Being this is a few years old, Im hoping you got...

Being this is a few years old, Im hoping you got this resolved. What did you find your answer to be? Having the same issue.. cooler tested okay.
Forum: General Q & A
02-28-2021, 02:54 PM
Replies: 3
Views: 538
Posted By Scottski

That sounds easy enough Ill get under the dash...

That sounds easy enough Ill get under the dash and start poking around this week. So at the cannon plug side of the boat harness in the engine bay, cut the orange at the plug and yank the big pin...
Forum: General Q & A
02-28-2021, 06:45 AM
Replies: 3
Views: 538
Posted By Scottski

Old 9 pin to newer 9 pin and wiring issues/ confusion

I recently posted a question regarding rebuilding my engine for a 79 Pantera. In short, I found a very clean 95 454 mag fully dressed for less than half what the rebuild was going to cost, so I got...
Forum: General Q & A
01-18-2021, 05:54 AM
Replies: 27
Views: 6,336
Posted By Scottski

Thank you GPM, I read about the added bolts...

Thank you GPM, I read about the added bolts upgrade. Ill talk to my machinist about it and explore that route. And no, I'm not going for max power. Someday in a newer lighter boat, but not this one.
Forum: General Q & A
01-17-2021, 04:20 PM
Replies: 27
Views: 6,336
Posted By Scottski

Even w/ a 2 bolt? Most seem to think thats a bad...

Even w/ a 2 bolt? Most seem to think thats a bad idea. If I do that, My option would be forged crank and keep my current flatt tappet cam. Im about 1500 over what I can realistically afford and cant...
Forum: General Q & A
01-17-2021, 01:11 PM
Replies: 27
Views: 6,336
Posted By Scottski

I finally got to examine the risers today. Looks...

I finally got to examine the risers today. Looks like the water is mixing basically at teh end of the tail at the transom. The risers are stainless, 6" rise and then they angle downward to exit the...
Forum: General Q & A
01-13-2021, 04:43 PM
Replies: 27
Views: 6,336
Posted By Scottski

I'm goin to investigate soon where exactly my...

I'm goin to investigate soon where exactly my exhaust and water mix in my risers. i was just outside looking at it and cant visually figure it out.
I may have to call the previous owner that...
Forum: General Q & A
01-13-2021, 03:24 PM
Replies: 27
Views: 6,336
Posted By Scottski

Bill K, please clear out your PM inbox so I can...

Bill K, please clear out your PM inbox so I can respond. Thanks
Forum: General Q & A
01-13-2021, 12:43 PM
Replies: 27
Views: 6,336
Posted By Scottski

First, thank you to everyone who has answered...

First, thank you to everyone who has answered thus far. This has been my first post on here and the wealth of knowledge from all of you is greatly appreciated.




Actually I snuck it in at the...
Forum: General Q & A
01-13-2021, 07:06 AM
Replies: 27
Views: 6,336
Posted By Scottski

In regards to swapping to a Gen 6, My concern was...

In regards to swapping to a Gen 6, My concern was with the flywheel side. So Ill ask here and see what answer I get, again, searching led me to a few contradicting answers.

Will my Driveplate or...
Forum: General Q & A
01-13-2021, 06:50 AM
Replies: 27
Views: 6,336
Posted By Scottski

That's more HP than I was planning for. I've...

That's more HP than I was planning for. I've been told by many about TRS that once I exceed 500 things can start to go wrong...



I appreciate that and actually thought about that as well. My...
Forum: General Q & A
01-12-2021, 05:16 PM
Replies: 27
Views: 6,336
Posted By Scottski

Thank you for that info. So I'm leaning more...

Thank you for that info. So I'm leaning more towards the Scat Forged assembly, So, what Cam should I be looking for? I would like to go to a Roller Cam and like the idea of the Comp Cams kits that...
Forum: General Q & A
01-12-2021, 03:28 PM
Replies: 27
Views: 6,336
Posted By Scottski

Bill, I'm guessing you meant Forged crank? ...

Bill, I'm guessing you meant Forged crank?


Are you asking about the boat? No, it is still the original Blue Gelcoat, white deck, white bottom
Forum: General Q & A
01-12-2021, 02:37 PM
Replies: 27
Views: 6,336
Posted By Scottski

And that brings up another question. If an...

And that brings up another question. If an assembly comes internally balanced, am I looking at then getting an internally balanced flywheel and harmonic Balancer to go with it?
Forum: General Q & A
01-12-2021, 02:31 PM
Replies: 27
Views: 6,336
Posted By Scottski

Thank you for the replies. I was thinking about...

Thank you for the replies. I was thinking about forged cranks but wondered if it was necessary for the HP id be making.

GPM, what cam might you suggest?
Forum: General Q & A
01-12-2021, 09:01 AM
Replies: 27
Views: 6,336
Posted By Scottski

Mark IV 496 Build help

Hello all, We recently picked up a '78 24 Pantera Sport, TRS 330, all original and in immaculate condition. Fresh water boat and climate controlled garage kept all of its life. The unfortunate part,...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.