Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: wwbobb
Showing results 1 to 18 of 18
Search took 0.00 seconds.
Forum: General Q & A
07-05-2013, 10:01 PM
Replies: 9
Views: 859
Posted By wwbobb

Update I finally took her out this week and...

Update

I finally took her out this week and full advance was stable at 34 degrees at WOT. Thank you 28Eliminator and Smitty for the education!

Warren
Forum: General Q & A
06-18-2013, 05:13 PM
Replies: 9
Views: 859
Posted By wwbobb

Thanks for the quick replies. Makes sense...

Thanks for the quick replies. Makes sense regarding no load conditions. This stuff ain't in the manual. I'll throw it in the river in a day or two and see what happens and report back.
Forum: General Q & A
06-18-2013, 04:31 PM
Replies: 9
Views: 859
Posted By wwbobb

Didn't want to run it that high on the hose. ...

Didn't want to run it that high on the hose. Figured it was all in at 3500. No knock sensor activity according to the scanner. I'm leaning toward the ECM but checksum comes back with no errors.
Forum: General Q & A
06-18-2013, 01:14 PM
Replies: 9
Views: 859
Posted By wwbobb

502EFI excessive advance

Hello all

I have a 1995 502efi completely stock other than Gil offshore exhaust. According to my Rinda Mercruiser scan tool, the advance is showing 40 degrees at 3500 rpm. I have base timing set...
Forum: General Q & A
05-01-2012, 06:33 PM
Replies: 7
Views: 2,068
Posted By wwbobb

Yeah. Wonderful ain't it. They are tough to...

Yeah. Wonderful ain't it. They are tough to find new and that is the cheapest I've seen.
Forum: General Q & A
05-01-2012, 04:10 PM
Replies: 7
Views: 2,068
Posted By wwbobb

http://www.classicindustries.com/truck/parts/g7951...

http://www.classicindustries.com/truck/parts/g7951.html

Rings included.
Forum: General Q & A
05-14-2006, 10:37 PM
Replies: 26
Views: 4,007
Posted By wwbobb

Re: Strange knocking from #8 area..

BadDog...any updates on this problem?
Forum: General Boating Discussion
01-07-2004, 10:21 PM
Replies: 10
Views: 1,442
Posted By wwbobb

If your using IE6, click tools, then internet...

If your using IE6, click tools, then internet options, then secuity tab, then trusted sites and add your banks url to the trusted sites list.

Warren
Forum: General Boating Discussion
11-19-2003, 12:07 AM
Replies: 18
Views: 1,589
Posted By wwbobb

Not exactly a "big" score, but I got a 24p...

Not exactly a "big" score, but I got a 24p Hydromotive in almost new condition for $158 including shipping. Made me happy :D

Warren
Forum: General Q & A
07-24-2003, 12:36 AM
Replies: 11
Views: 1,987
Posted By wwbobb

Steve, They are the pins on either end of...

Steve,

They are the pins on either end of the trim cylinder rams. Should be a plastic cap covering the nuts. Just measure from the center of the exposed screws in the center of the caps.
...
Forum: General Q & A
07-24-2003, 12:15 AM
Replies: 11
Views: 1,987
Posted By wwbobb

Maximum up trim(not trailer position)is measured...

Maximum up trim(not trailer position)is measured from center to center of the ram mount pins and is 21 3/4 inches on a Bravo One. You should check this before you run it. If the trim is too far...
Forum: General Q & A
07-17-2003, 12:05 PM
Replies: 2
Views: 906
Posted By wwbobb

Manual sez 12-16 ft lbs. No sealant on the...

Manual sez 12-16 ft lbs. No sealant on the threads.

Warren
Forum: General Q & A
09-18-2002, 11:32 PM
Replies: 5
Views: 17,377
Posted By wwbobb

According to the Merc service manual, the 7.4L...

According to the Merc service manual, the 7.4L with flat tappets is: I238 .282"(lobe lift? not sure how this translates to actual lift) E234 LL .271" @.050, rollers I209 LL.282" E209 LL .284"...
Forum: General Q & A
09-16-2002, 08:01 PM
Replies: 3
Views: 1,133
Posted By wwbobb

Dennis, Thank you for the reply. I will try...

Dennis,

Thank you for the reply. I will try as you suggested.

Warren
Forum: General Q & A
09-16-2002, 11:44 AM
Replies: 3
Views: 1,133
Posted By wwbobb

Question for Mr. Moore-502 EFI

Dennis,

Regarding the 502 cam thread, I am using the Crane H-278 in a 95 502 EFI with the stock ECU and GIL manifolds. Would increasing the fuel rail pressure provide any benefit with this...
Forum: General Boating Discussion
08-25-2002, 02:27 PM
Replies: 13
Views: 2,231
Posted By wwbobb

Steve, I had a painted Eagle trailer that...

Steve,

I had a painted Eagle trailer that lasted about 6 years. It rusted from the inside out to the point where stuctural integrity was severely compromised. A buddy cut it up and was amazed by...
Forum: Baja
12-06-2001, 02:51 AM
Replies: 262
Views: 56,795
Posted By wwbobb

Post Dirtlawyer, I didn't get radical with the...

Dirtlawyer,

I didn't get radical with the rebuild. Fairly mild bump in camming(Crane flat hydraulic E234 .525 I222 .529 114LSA) and Gil Offshore exhaust were the only major changes. Reliability...
Forum: Baja
12-04-2001, 12:39 AM
Replies: 262
Views: 56,795
Posted By wwbobb

Post 95 272 502EFI just rebuilt with cam and exhaust

95 272 502EFI just rebuilt with cam and exhaust
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.