Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: nightmoves
Showing results 1 to 25 of 56
Search took 0.03 seconds.
Forum: Wanted
10-28-2021, 01:26 PM
Replies: 3
Views: 394
Posted By nightmoves

Outboard bracket

I have a stainless marine triple.
Forum: Wanted
09-15-2021, 06:25 PM
Replies: 2
Views: 610
Posted By nightmoves

19 to 26 spline propshaft adaptors

looking for 2 19 to 26 SSM propshaft spline adaptors
Forum: Swap Shop
09-14-2021, 04:44 PM
Replies: 2
Views: 537
Posted By nightmoves

Holley 1050 8090

I am a buyer at $500
Forum: Swap Shop
04-03-2021, 08:17 AM
Replies: 4
Views: 909
Posted By nightmoves

Steering ram or Rams ??

What diameter , What length ? Do you have one or More ? $300 for used unknown Ram ? Do they leak under pressure ?
Forum: Apache
04-29-2015, 08:03 AM
Replies: 4
Views: 1,299
Posted By nightmoves

Rear floor tank capacity 41

my 1986 has 125 gallon capacity in the belly tank under the cockpit sole
Forum: Swap Shop
04-27-2015, 08:34 AM
Replies: 9
Views: 3,144
Posted By nightmoves

give me a call I have many quality parts from...

give me a call I have many quality parts from years of running offshores + cash
614 205 5401
Forum: Swap Shop
04-12-2015, 11:22 AM
Replies: 23
Views: 2,891
Posted By nightmoves

would these work on the 480 ?

would these work on the 480 ?
Forum: Wanted
01-05-2015, 10:41 AM
Replies: 4
Views: 498
Posted By nightmoves

did you get the pics from my phone ?

did you get the pics from my phone ?
Forum: Wanted
12-24-2014, 02:47 PM
Replies: 4
Views: 498
Posted By nightmoves

I have a Capilano 1275 in excellent condition ,...

I have a Capilano 1275 in excellent condition , it has the backing plate and the steering wheel receiver as well, PM me or call 614 205 5401
Forum: Wanted
12-24-2014, 02:38 PM
Replies: 15
Views: 1,407
Posted By nightmoves

I have a set of standard 502 pistons with the...

I have a set of standard 502 pistons with the original rings on them ! These could be washed oiled and installed.
i got them after they were run on the dyno once to set a baseline in engine...
Forum: Swap Shop
12-24-2013, 11:46 AM
Replies: 24
Views: 3,345
Posted By nightmoves

Primecut, perhaps one should take a closer look...

Primecut, perhaps one should take a closer look at the water passages
Forum: Swap Shop
12-14-2013, 02:20 PM
Replies: 15
Views: 2,320
Posted By nightmoves

Hey Kid, not to crash thread but you should have...

Hey Kid, not to crash thread but you should have received payment. Thursday via certified mail for the swim platform and half the shipping cost as you indicated
Forum: Wanted
10-11-2012, 12:57 PM
Replies: 0
Views: 956
Posted By nightmoves

verado power steering pump

looking for a mercury verado power steering pump the part # for the shorter leads and no hoses is 892 440 A17, I believe the pump assembly w/ the longer leads is 892 440 A19 .The pump will be mounted...
Forum: Wanted
09-06-2012, 12:47 PM
Replies: 4
Views: 420
Posted By nightmoves

#5 lower gearsets

I think i have these. To simplify things can you send me the part # ??
Forum: Wanted
09-05-2012, 09:36 AM
Replies: 4
Views: 584
Posted By nightmoves

3a's

I HAVE A SET OF LOW HOUR , FRESHWATER 3A's. 1.68 RATIO. JUST HAD THEM PROFESSIONALLY GONE THROUGH W/ DOCUMENTATION FOR THE WORK. 614 205 5401 OR [email protected]
Forum: Wanted
06-08-2012, 07:58 AM
Replies: 7
Views: 596
Posted By nightmoves

3a's

email sent a couple of days ago
Forum: Wanted
06-05-2012, 05:46 PM
Replies: 7
Views: 596
Posted By nightmoves

3A's

I have a fresh pair 1:68 ratio
Forum: Swap Shop
12-24-2011, 02:15 PM
Replies: 11
Views: 1,172
Posted By nightmoves

Smile Rings

Not To But In; I Think I Have A Couple Of Sets Of Rings For 502
Forum: Swap Shop
06-06-2011, 11:08 PM
Replies: 21
Views: 1,989
Posted By nightmoves

Drive Bottles

Do youi have alarms for these?
Forum: Swap Shop
06-03-2011, 07:02 PM
Replies: 2
Views: 537
Posted By nightmoves

2 502's

I Have 2 FRESH 502 cu.in Lingenfelter built engines . Long blocks Gil 12 qt. pan to intake. You would need Carb etc. Therse have the large oval port steel heads w/ Lingenfelter pro mod. option. These...
Forum: Wanted
05-31-2011, 10:16 PM
Replies: 6
Views: 707
Posted By nightmoves

dominator flame arrestor

Is this same part # (6FA -1050 - 10 -3SS) ?
Forum: Wanted
05-27-2011, 11:27 AM
Replies: 6
Views: 707
Posted By nightmoves

Dom. Flame Arrestors

Looking For Two, The Thinner Circa 2-3" Version
Forum: Wanted
05-02-2011, 12:22 PM
Replies: 5
Views: 619
Posted By nightmoves

do you still have a trim pump?

do you still have a trim pump?
Forum: Swap Shop
05-02-2011, 12:03 PM
Replies: 5
Views: 738
Posted By nightmoves

mounts

what type of mounts do you have/
Forum: Swap Shop
03-10-2010, 04:01 PM
Replies: 0
Views: 448
Posted By nightmoves

Smile #4,#5 lower rear tiebar mounts

Looking for a pair of the mounts only, these are the ones that bolt to the flat area at the bottom, rear of the gear casing on 4's and 5's
Showing results 1 to 25 of 56
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.